전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

MPF5024AMBA0ES 데이터시트(PDF) 22 Page - NXP Semiconductors

부품명 MPF5024AMBA0ES
상세설명  Power management integrated circuit (PMIC) for high performance applications
PDF  93 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  NXP [NXP Semiconductors]
홈페이지  http://www.nxp.com
Logo NXP - NXP Semiconductors

MPF5024AMBA0ES 데이터시트(HTML) 22 Page - NXP Semiconductors

Back Button MPF5024AMBA0ES Datasheet HTML 18Page - NXP Semiconductors MPF5024AMBA0ES Datasheet HTML 19Page - NXP Semiconductors MPF5024AMBA0ES Datasheet HTML 20Page - NXP Semiconductors MPF5024AMBA0ES Datasheet HTML 21Page - NXP Semiconductors MPF5024AMBA0ES Datasheet HTML 22Page - NXP Semiconductors MPF5024AMBA0ES Datasheet HTML 23Page - NXP Semiconductors MPF5024AMBA0ES Datasheet HTML 24Page - NXP Semiconductors MPF5024AMBA0ES Datasheet HTML 25Page - NXP Semiconductors MPF5024AMBA0ES Datasheet HTML 26Page - NXP Semiconductors Next Button
Zoom Inzoom in Zoom Outzoom out
 22 / 93 page
background image
NXP Semiconductors
PF5024
Power management integrated circuit (PMIC) for high performance applications
PF5024
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2020. All rights reserved.
Product data sheet
Rev. 1 — 15 April 2020
22 / 93
When the _SEQ[7:0] bits of all regulators and PGOOD used as a GPIO are set to 0x00
(OFF) and a power on event is present, the device moves to the run state in slave mode.
In this mode, the device is enabled without any voltage regulator or GPO enabled. If the
RESETBMCU is not programed in a power up sequence slot, it is released when the
device enters the run state.
The slave mode is a special case of the power up sequence to address the scenario
where the PF5024 is working as a slave PMIC, and supplies are meant to be enabled
by the MCU during the system operation. In this scenario, if RESETBMCU is used, it is
connected to the master RESETBMCU pin.
Figure 8 provides an example of the power up/down sequence coming from the Off
modes.
aaa-030047
System On
End of
PWRUP
End of
PWRDN
Power down Seq.
Run to Off
Power up Seq.
Off to Run
INTB
SW2
SW3
SW4
SW1
RESETBMCU
Start of
PWRDN
Figure 8. Power up/down sequence between Off and system On state
When transitioning from Standby mode to Run mode, the power up sequencer is
activated only if any of the external regulators is re-enabled during this transition. If none
of the regulators toggle from Off to On and only voltage changes are being performed
when entering or exiting Standby mode, the changes for the voltage regulators are made
simultaneously rather than going through the power up sequencer.
Figure 9 shows an example of the power up/down sequence when transitioning between
Run and Standby modes.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com