| 전자부품 데이터시트 검색엔진 |
|
AT90PWM2 데이터시트(PDF) 209 Page - ATMEL Corporation |
|
|
|||||||||||||||||||||||||||||
AT90PWM2 데이터시트(HTML) 209 Page - ATMEL Corporation |
|
209 / 365 page ![]() 209 AT90PWM2/3 4317B–AVR–02/05 The recommendations of the maximum receiver baud rate error was made under the assumption that the Receiver and Transmitter equally divides the maximum total error. There are two possible sources for the receivers baud rate error. The Receiver’s system clock (XTAL) will always have some minor instability over the supply voltage range and the temperature range. When using a crystal to generate the system clock, this is rarely a problem, but for a resonator the system clock may differ more than 2% depending of the resonators tolerance. The second source for the error is more controllable. The baud rate generator can not always do an exact division of the system frequency to get the baud rate wanted. In this case an UBRR value that gives an acceptable low error can be used if possible. Multi-processor Communication Mode This mode is available only in USART mode, not in EUSART. Setting the Multi-processor Communication mode (MPCM) bit in UCSRA enables a fil- tering function of incoming frames received by the USART Receiver. Frames that do not contain address information will be ignored and not put into the receive buffer. This effectively reduces the number of incoming frames that has to be handled by the CPU, in a system with multiple MCUs that communicate via the same serial bus. The Trans- mitter is unaffected by the MPCM setting, but has to be used differently when it is a part of a system utilizing the Multi-processor Communication mode. MPCM Protocol If the Receiver is set up to receive frames that contain 5 to 8 data bits, then the first stop bit indicates if the frame contains data or address information. If the Receiver is set up Table 76. Recommended Maximum Receiver Baud Rate Error for Normal Speed Mode (U2X = 0) D # (Data+Parity Bit) Rslow (%) Rfast (%) Max Total Error (%) Recommended Max Receiver Error (%) 5 93.20 106.67 +6.67/-6.8 ± 3.0 6 94.12 105.79 +5.79/-5.88 ± 2.5 7 94.81 105.11 +5.11/-5.19 ± 2.0 8 95.36 104.58 +4.58/-4.54 ± 2.0 9 95.81 104.14 +4.14/-4.19 ± 1.5 10 96.17 103.78 +3.78/-3.83 ± 1.5 Table 77. Recommended Maximum Receiver Baud Rate Error for Double Speed Mode (U2X = 1) D # (Data+Parity Bit) R slow (%) R fast (%) Max Total Error (%) Recommended Max Receiver Error (%) 5 94.12 105.66 +5.66/-5.88 ± 2.5 6 94.92 104.92 +4.92/-5.08 ± 2.0 7 95.52 104,35 +4.35/-4.48 ± 1.5 8 96.00 103.90 +3.90/-4.00 ± 1.5 9 96.39 103.53 +3.53/-3.61 ± 1.5 10 96.70 103.23 +3.23/-3.30 ± 1.0 |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |