| 전자부품 데이터시트 검색엔진 |
|
AT90PWM2 데이터시트(PDF) 309 Page - ATMEL Corporation |
|
|
|||||||||||||||||||||||||||||
AT90PWM2 데이터시트(HTML) 309 Page - ATMEL Corporation |
|
309 / 365 page ![]() 309 AT90PWM2/3 4317B–AVR–02/05 DC Characteristics Note: 1. “Max” means the highest value where the pin is guaranteed to be read as low 2. “Min” means the lowest value where the pin is guaranteed to be read as high 3. Although each I/O port can sink more than the test conditions (20 mA at VCC = 5V, 10 mA at VCC = 3V) under steady state conditions (non-transient), the following must be observed: TQFP and MLF Package: 1] The sum of all IOL, for all ports, should not exceed 400 mA. 2] The sum of all IOL, for ports A0 - A7, G2, C3 - C7 should not exceed 300 mA. 3] The sum of all IOL, for ports C0 - C2, G0 - G1, D0 - D7, XTAL2 should not exceed 150 mA. 4] The sum of all IOL, for ports B0 - B7, G3 - G4, E0 - E7 should not exceed 150 mA. 5] The sum of all IOL, for ports F0 - F7, should not exceed 200 mA. If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test condition. TA = -45 °C to +105°C, VCC = 2.7V to 5.5V (unless otherwise noted) Symbol Parameter Condition Min. Typ. Max. Units VIL Input Low Voltage Except XTAL1 pin TBD TBD (1) V VIL1 Input Low Voltage XTAL1 pin, External Clock Selected TBD TBD (1) V VIH Input High Voltage Except XTAL1 and RESET pins TBD (2) TBD V VIH1 Input High Voltage XTAL1 pin, External Clock Selected TBD (2) TBD V VIH2 Input High Voltage RESET pin TBD (2) TBD V VOL Output Low Voltage (3) (Ports A, B, C, D, E, F; G) IOL = 20 mA, VCC = 5V IOL = 10 mA, VCC = 3V TBD V VOH Output High Voltage (4) (Ports A, B, C, D, IOH = -20 mA, VCC = 5V IOH = -10 mA, VCC = 3V TBD V IIL Input Leakage Current I/O Pin V CC = 5.5V, pin low (absolute value) TBD µA IIH Input Leakage Current I/O Pin V CC = 5.5V, pin high (absolute value) TBD nA R RST Reset Pull-up Resistor TBD TBD k Ω Rpu I/O Pin Pull-up Resistor TBD TBD k Ω ICC Power Supply Current Active 8 MHz, VCC = 3V TBD mA Active 16 MHz, VCC = 5V TBD mA Idle 8 MHz, VCC = 3V TBD mA Idle 16 MHz, VCC = 5V TBD mA Power-down mode (5) WDT enabled, VCC = 3V TBD TBD µA WDT disabled, VCC = 3V TBD TBD µA VACIO Analog Comparator Input Offset Voltage VCC = 5V Vin = VCC/2 TBD mV IACLK Analog Comparator Input Leakage Current VCC = 5V Vin = VCC/2 TBD TBD nA tACID Analog Comparator Propagation Delay VCC = 2.7V VCC = 5.0V TBD TBD ns |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |