| 전자부품 데이터시트 검색엔진 |
|
WM8581 데이터시트(PDF) 47 Page - Wolfson Microelectronics plc |
|
|
|||||||||||||||||||||||||||||
WM8581 데이터시트(HTML) 47 Page - Wolfson Microelectronics plc |
|
47 / 94 page ![]() Product Preview WM8581 w PP Rev 1.0 March 2006 47 The oscillator XOUT pin has one control bit as shown in Table 37. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R51 PWRDN 2 33h 0 OSCPD 0 Oscillator XOUT Power Down 0 = Power Up XOUT (crystal mode) 1 = Power Down XOUT (CMOS clock input mode) Table 37 Oscillator Control PHASE-LOCKED LOOP (PLL) The WM8581 has two on-chip phase-locked loop (PLL) circuits which can be used to synthesise two independent clock signals (PLLACLK and PLLBCLK) from the external oscillator clock. The PLLs can be used to: • Generate clocks necessary for the S/PDIF receiver to lock on to and recover S/PDIF data from an incoming S/PDIF data stream. • Generate clocks which may be used to drive the MCLK and/or CLKOUT pins. • Generate clocks which may be used by the S/PDIF transmitter to encode and transmit a S/PDIF data stream. • Generate clocks which may be used as the master clock source for the the ADC and DACs. • Generate clocks which may be used by the master mode clock generator to generate the BCLK and LRCLK signals for the digital audio interfaces. The PLLs can be enabled or disabled using the register bits shown in Table 38. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION 1 PLLAPD 1 R51 PWRDN 2 33h 2 PLLBPD 1 PLL Power Down Control 0 = Power Up PLL 1 = Power Down PLL Table 38 PLL Power Down Control The PLLs have two modes of operation: • PLL S/PDIF Receive Mode (Selected if S/PDIF Receiver Enabled) In S/PDIF receive mode, PLLA is automatically controlled by the S/PDIF receiver to allow the receiver to use PLLA to track and lock on to the incoming S/PDIF data stream. In this case, CLK1 is automatically maintained at a constant frequency of 256fs relative to the sample rate of the recovered S/PDIF stream. PLLB must be configured to produce CLK2, a specific reference clock for the S/PDIF receiver. PLLACLK may be used as a 256fs or 128fs (selectable – refer to Table 43) master clock source when in S/PDIF receiver mode. PLLBCLK is not available and must not be selected as the clock source for any internal function when the S/PDIF receiver is enabled. If the sample frequency of the incoming stream is changed and PLLA is forced to unlock in order to track to the new sample frequency, the PLLACLK signal will be stopped until the S/PDIF receiver has locked to the incoming stream at the new sample frequency. If the incoming S/PDIF stream stops, the PLLA_ N and PLLA_K values will be frozen and the PLLACLK will continue at the frequency set by the last recovered S/PDIF stream. Refer to Table 39 and Table 41 for details of the registers available for configuration in this mode. Refer to the S/PDIF Receive Mode Clocking section on page 52 for full details. • PLL User Mode (Selected if S/PDIF Receiver Disabled) In user mode, the user has full control over the function and operation of both PLLA and PLLB. In this mode, the user can accurately specify the PLL N and K multiplier values and the pre and post-scale divider values and can hence fully control the generated clock frequencies. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |