SPSB081C3 datasheet(55/135 Pages) STMICROELECTRONICS

55 / 135 page

Symbol

Parameter

Condition

Min

Typ Max Unit Item

Current consumption for

HS drivers

Wake-up OFF except LIN transceiver;

Tj = 25°C

µA

IV(V1stby _HS,85)(3)

V1_standby

cyclic sense enabled; (5)

HSx (x=3;4) ON;

CAN OFF;

Wake-up OFF except LIN transceiver;

Tj = 85°C

570 1000

A.073

1. Conditions for specified current consumption:

•

VLIN > (VSREG-1.5V)

•

(CAN_H – CAN_L) < 0.4V or (CAN_H – CAN_L) > 1.2V

•

VWU < 1V or VWU > (VSREG – 1.5 V)

•

LIN wake-up is possible, CAN wake up disabled, WUx_EN register set to 0

2. In SPSB081Cx it is mandatory to keep wake-up source capability (CANFD or wake-up pin) and in that case an additional

contribution of IV(VBAT_WU,x) or IV(CANWU,x) has to be considered.

3. Guaranteed by design.

4. Current consumption adders of features defined for SBC V1 stby mode or for SBC VBAT stby mode (unless otherwise

specified).

5. Current consumption adder while only one HS is turned on with no load.

5.1

Oscillator

The voltages are referred to ground and currents are assumed positive, when the current flows into the pin. 6 V <

VS< 28 V; 6 V < VSREG< 28 V; Tj = -40°C... 150°C, unless otherwise specified.

Table 28. Oscillator

Symbol

Parameter

Condition

Min

Typ

Max

Unit

Item

FCLK1(1)(2)

Oscillation frequency

0.80

1.0

1.20

MHz

A.018

FCLK2(1)

Oscillation frequency

12.8

16.0

19.2

MHz

A.019

1. 1 MHz clock is used in standby mode. 16 MHz clock is used in active mode.

2. The clock frequency is further reduced in standby mode to sustain a very low quiescent current.

5.2

Power-on reset (VSREG)

All outputs open; Tj = from -40°C to 150°C, unless otherwise specified

Table 29. Power-on reset

Symbol

Parameter

Condition

Min

Typ

Max

Unit

Item

VPOR_R

VPOR threshold

VSREG rising

3.45

4.5

A.020

VPOR_F

VPOR threshold

VSREG falling (1)

2.3

3.55

A.021

1. This threshold is valid if VSREG had already reached VPOR_R(max) previously.

5.3

Voltage regulator V1

The voltages are referred to ground and currents are assumed positive, when the current flows into the pin. 4.5 <

VS< 28 V; 4.5V < VSREG< 28 V; Tj = from -40°C to 150°C, unless otherwise specified.

The same parameter values in both 5 V and 3.3 V conditions apply unless otherwise specified.

SPSB081

Oscillator

DS14048 - Rev 1

page 55/135

SPSB081C3 데이터시트(PDF) 55 Page - STMicroelectronics

SPSB081C3 데이터시트(HTML) 55 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL