| 전자부품 데이터시트 검색엔진 |
|
SPSB081C3 데이터시트(PDF) 67 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
SPSB081C3 데이터시트(HTML) 67 Page - STMicroelectronics |
|
67 / 135 page ![]() Symbol Parameter Condition Min Typ Max Unit Item VDIFF_Arb Differential output voltage in dominant state during arbitration: VCANHdom-VCANLdom VTXDC=VTXDCLOW ; RL=2240 Ω 1.5 5 V E.024 VDIFF,dom_ext Differential output voltage in dominant state on extended bus load range: VCANHdom-VCANLdom VTXDC=VTXDCLOW ; RL=45 Ω … 70 Ω 1.4 3.3 V E.025 VDIFF,domVsLow Differential output voltage in dominant state: VCANHdom-VCANLdom at low VSREG VTXDC=VTXDCLOW ; RL=50 Ω … 65 Ω; 5 V < VSREG < 5.5 V 1.35 3 V E.026 VDIFF,dom_ext_ VsLow Differential output voltage in dominant state: VCANHdom -VCANLdom with 45Ω … 70Ω load at low VSREG VTXDC=VTXDCLO W; RL=45 … 70 Ω; 5 V < VSREG < 5.5 V (1) 1.25 3.3 V E.027 VSYM Driver symmetry VSYM = (VCANH + VCANL)/VCANSUP VCANSUP = 5 V (2) RL = 60 Ω ± 1%; fTXDC = 1MHz (3); CSPLIT = 4.7 nF (+-5%) 0.9 1 1.1 E.028 IOCANH,dom (-3 V) CANH output current in dominant state VTXDC = VTXDCLOW; VCANH= -3 V..18 V -115 115 mA E.029 IOCANL,dom (18 V) CANL output current in dominant state VTXDC = VTXDCLOW; VCANL = -3 V..18 V -115 115 mA E.030 IOCANL,dom (40 V) CANL output current in dominant state VTXDC = VTXDCLOW; VCANL = 40 V; VSREG = 40 V 0 115 mA E.032 1. VSREG at device pin after reverse battery protection, while application is supplied with 6V. Operating condition has to be adapted, if higher voltage drop occur in the application. 2. Put into the datasheet, if it is an internal voltage. If it is an external pin, it should be supplied externally. 3. Measurement equipment input load <20 pF, >1 MΩ, guaranteed by E.025, E.026, E.029, E.030, E.053, E.054 measurements. Table 44. CAN transmitter recessive output characteristics, CAN normal mode Symbol Parameter Condition Min Typ Max Unit Item VCANHrec CANH voltage level in recessive state (normal mode) VTXDC = VTXDCHIGH; no load 2 2.5 3 V E.033 VCANLrec CANL voltage level in recessive state (normal mode) VTXDC = VTXDCHIGH; no load 2 2.5 3 V E.034 VDIFF,recOUT Differential output voltage in recessive state (normal mode): VTXDC = VTXDCHIGH; no load -50 50 mV E.035 SPSB081 CAN FD transceiver DS14048 - Rev 1 page 67/135 |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |