H7CC-R11WD datasheet(16/66 Pages) OMRON

16 / 66 page

H7CC-A

Counter

Note: Not displayed when the H7AN compatibility function is ON.

* The display shows 5 kHz, but the maximum

counting speed is 10 kHz.

Note: Displayed only when the output mode is

C, R, K-1, P, Q, A, or K-2.

Note: Displayed only when the

output mode is C, R, K-1,

P, Q, A, or K-2.

Note: Displayed for output modes

other than D, L, and H.

HOLD cannot be set when

the output mode is K-2.

*7 Set each digit using the individual

UP1 to UP4 Keys (DW1 to DW4 Keys).

*7 Set each digit using the individual

UP1 to UP4 Keys (DW1 to DW4 Keys).

* Use UP1+UP3 to move up and

DW1+DW3 to move down

(1 ms)

(20 ms)

(30 Hz)

(5 kHz)

(0.50 s) (99.99 s)

(0.01 s)

(0.50 s) (99.99 s)

(0.01 s)

(99.999)

(1.000)

(0.001)

(0.50 s)

(99.99 s)

(0.01 s)

(OFST)

(ABS)

Note: Displayed only when the configuration selection mode is set

to the 2-stage counter

2cnt and there is a forecast value setting.

Note: Displayed only when the configuration selection

mode is set to the 2-stage counter

2cnt.

Note: Displayed only when the output mode is

bcnt

From

Output

time

(OTIM)

NPN/PNP

input mode

(IMOD)

Prescale

value

(PSCL)

Counting

speed

(CNTS)

Reset input

signal width

(IFLT)

Decimal

point position

(DP)

(No decimal

point)

(One digit after

decimal point)

(Two digits after

decimal point)

(Three digits after

decimal point)

(PNP input)

(NPN input)

When using as a 2-stage preset counter

One-shot

output 2

time

(OTM2)

One-shot

output 1

time

(OTM1)

(0.01 s) (99.99 s)

(Outputs held)

Note: Displayed only when the

output mode is C, R, K-1,

P, Q, A, or K-2.

When using as a batch counter

One-shot

output 2

time

(OTM2)

• Set the counting speed using the UP1 Key (DW1 Key).

• Set the Reset input signal width using the UP1 Key (DW1 Key).

• Set the decimal point position using the UP1 Key (DW1 Key).

• Set each digit using the individual

UP1 to UP4 Keys (DW1 to DW4 Keys).

• Set each digit using the individual UP1 Key (DW1 Key).

• Set the NPN/PNP input mode using the UP1 Key (DW1 Key).

------

-----.-

----.--

---.---

0.01

99.99

0.50

30h

1 s

0.001

99.999

1.000

pnp

npn

20 s

0.50

hold 0.01 99.99

0.01 0.50 99.99

0.01

99.99

0.50

0.01

99.99

0.50

0.01

99.99

(999999)

(1)

999999

(999999)

(1)

999999

ofst

abs

(999999)

(1)

999999

From previous

page

To previous

page

If the output time is 0.00,

hold is displayed.

Note:Displayed only when the

output mode is C, R, K-1, P,

Q, or A.

Note:Displayed only when the

output mode is C, R, K-1, P,

Q, or A.

(0.50 s) (99.99 s)

(0.01 s)

Twin Counter

Output 2

output

time

(OTM2)

Output 1

output

time

(OTM1)

(0.50 s) (99.99 s)

(0.01 s)

• Make the absolute value setting and forecast setting using

the UP1 Key (DW1 Key).

Absolute value

setting/forecast

value setting

(SETM)

• Set each digit using the individual UP1 to UP6 Keys (DW1 to DW6 Keys).

Forecast

setting

upper limit

(PL-H)

Set value

upper limit

(SL-H)

Batch count

upper limit

(BL-H)

0.50

otm2

0.50

otm2

hold

otm1

0.50

otm2

0.50

otm1

0.50

otim

30hz

cnts

999999

sl-h

pl-h

999999

bl-h

abs

setm

npn

imod

1.000

pscl

------

20m5

iflt

H7CC-R11WD 데이터시트(PDF) 16 Page - Omron Electronics LLC

H7CC-R11WD 데이터시트(HTML) 16 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66

데이터시트 다운로드

링크 URL