H7CC-R11WD datasheet(19/66 Pages) OMRON

19 / 66 page

H7CC-A

Counter

Absolute Value Setting/Forecast Value Setting (setm)

For the 2 count output mode, an absolute value setting (abs) or

forecast value setting (ofst) can be set for set value 1.

If the absolute value setting is used, specify an absolute value

(deviation from 0).

If the forecast value setting is used, specify set value 1 as the forecast

set value (deviation with respect to set value 2).

The forecast output (output 1) turns ON when the present value

reaches the forecast value.

If the forecast set value is greater than or equal to the set value, the

forecast output (output 1) will turn ON as soon as counting starts.

Set Value Upper Limit (sl-h)

Set the upper limit for the set value when it is set in run mode.

The setting can be made from 1 to 999999 for 6-digit models.

Forecast Set Upper Limit (pl-h)

Set the upper limit for the forecast set value.

The setting can be made from 1 to 999999 for 6-digit models.

Batch Count Upper Limit (bl-h)

Set the upper limit for the batch count value. The setting can be made

from 1 to 999999 for 6-digit models.

Key Protect Level (kypt)

Set the key protect level.

Refer to Key Protect Level on page 40.

Output ON Count Alarm Set Value (on-a, on1a, on2a)

The output ON count for notifying the replacement time can be set.

For details, refer to page 41.

Output ON Count Monitor Value (on-c)

The monitor value is only displayed. It cannot be set.

The output ON count will be 1,000 times the displayed value.

ON Count Monitor Values for Outputs 1 and 2 (OUT1 and

OUT2) (on1c and on2c)

The monitor value for output 1 and 2 (OUT1 and OUT2) is only

displayed. It cannot be set.

The output ON count will be 1,000 times the displayed value.

Output Allocation (Settings applicable to only H7CC-

@W(U)@) (otst)

Set the allocation of outputs 1 and 2 (OUT1 and OUT2). If output

allocation is OFF, output 1 (OUT1) is allocated to terminals (12) and

(13), and output 2 (OUT2) is allocated to terminals (3), (4), and (5). If

output allocation is ON, output 1 (OUT1) is allocated to terminals (3),

(4), and (5), and output 2 (OUT2) is allocated to terminals (12) and

(13).

Output inversion (ot-i, ot1i, ot2i)

Set logical inversion of output ON/OFF. In the case of two outputs, it

is possible to individually set output inversion for each of output 1 and

output 2 (OUT1 and OUT2). If output inversion is n-o (Normally

Open), the output turns ON when the set value is reached. If output

inversion is n-c (Normally close), the output turns OFF when the set

value is reached.

Memory back up (bkvp)

Set the present value and the output state memory backup. If memory

backup is available, the present value and output state are recovered

to the state prior to power interruption. If memory backup is not

available, the present value and output state are recovered to the

reset state.

H7AN Compatibility Function (h7an)

When the present value being decremented exceeds 0, make the

setting to start counting from 999999. When this function is ON, the

value becomes 999999 after 0, and when this function is OFF, the

count is in accordance with the output mode. The H7AN Compatibility

Function is enabled only when 1-stage preset counter, 2-stage preset

counter, and total and preset counter are selected, and is displayed

in the function setting mode. It is not displayed when batch counter,

dual counter, or twin counter are selected. This function enables the

same operation when the H7AN is replaced with the H7CC.

Set value 2

Set value 1

Control output 1 (OUT1)

Control output 2 (OUT2)

Count value

Example: F Mode

Set value

Forecast

value

Forecast set value

Forecast output (OUT1)

Control output (OUT 2)

Count value

Example: F Mode

H7CC-R11WD 데이터시트(PDF) 19 Page - Omron Electronics LLC

H7CC-R11WD 데이터시트(HTML) 19 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66

데이터시트 다운로드

링크 URL