| 전자부품 데이터시트 검색엔진 |
|
VT8235 데이터시트(PDF) 85 Page - VIA Technologies, Inc. |
|
|
|||||||||||||||||||||||||||||
VT8235 데이터시트(HTML) 85 Page - VIA Technologies, Inc. |
|
85 / 145 page ![]() VT8235 V-Link South Bridge Revision 1.22 October 24, 2002 -79- Device 17 Function 0 Power Management Registers UrpuytvrÃDp XrÃ8rp System Management Bus-Specific Configuration Registers Offset D1-D0 – SMBus I/O Base ......................................RW 15-4 I/O Base (16-byte I/O space) ............... default = 00h 3-0 Fixed ................................ always reads 0001b Offset D2 – SMBus Host Configuration ..........................RW 7-4 Reserved ........................................ always reads 0 3 SMBus Interrupt Type 0 SMI .................................................... default 1 SCI 2 Reserved ........................................ always reads 0 1 SMBus Interrupt Enable 0 Disable SCI / SMI ................................. default 1 Enable SCI / SMI 0 SMBus Host Controller Enable 0 Disable SMB controller functions ......... default 1 Enable SMB controller functions Offset D3 – SMBus Host Slave Command ......................RW 7-0 SMBus Host Slave Command Code ......... default=0 Offset D4 – SMBus Slave Address for Port 1..................RW 7-1 SMBus Slave Address for Port 1 ............... default=0 0 Read / Write for Shadow Port 1 Offset D5 – SMBus Slave Address for Port 2..................RW 7-1 SMBus Slave Address for Port 2 ............... default=0 0 Read / Write for Shadow Port 2 Offset D6 – SMBus Revision ID ....................................... RO 7-0 SMBus Revision Code SMB GPIO Slave Command Codes SMBus Command Code 0 – GPIO Slave Input Port ...... RO 7-0 Input Data ...................................... default per pins Reflects the incoming logic levels of the pins, regardless of whether the pin is defined as an input or an output. Writes to this register have no effect. SMBus Command Code 1 – GPIO Slave Output Port .. RW 7-0 Output Data ..............................................default = 0 Controls the levels of the GPIO output pins defined as outputs. Bit values in this register have no effect on pins defined as inputs. Reads from this register reflect the saved value last written, not the actual pin value. SMBus Cmd Code 2 – GPIO Slave Polarity Inversion.. RW 7-0 Polarity Inversion .................................default = 0Fh This register enables polarity inversion of pins defined as inputs by Command Code 3. 0 Corresponding pin’s polarity unchanged 1 Corresponding pin’s polarity inverted SMBus Cmd Code 3 – GPIO Slave I/O Configuration.. RW 7-0 Input / Output Configuration ........... default = 0FFh This register configures the directions of the I/O pins. 0 Corresponding pin is an output 1 Corresponding pin is an input ............... default |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |