| 전자부품 데이터시트 검색엔진 |
|
WM8994ECS/R 데이터시트(PDF) 138 Page - Cirrus Logic |
|
|
|||||||||||||||||||||||||||||
WM8994ECS/R 데이터시트(HTML) 138 Page - Cirrus Logic |
|
138 / 363 page ![]() WM8994 138 Rev 4.6 REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION 0 DCS_ENA_CHAN_0 0 DC Servo enable for HPOUT1L 0 = Disabled 1 = Enabled R88 (0058h) DC Servo Readback 9:8 DCS_CAL_COMPL ETE [1:0] 00 DC Servo Complete status 0 = DAC Write or Start-Up DC Servo mode not completed. 1 = DAC Write or Start-Up DC Servo mode complete. Bit [1] = HPOUT1R Bit [0] = HPOUT1L 5:4 DCS_DAC_WR_CO MPLETE [1:0] 00 DC Servo DAC Write status 0 = DAC Write DC Servo mode not completed. 1 = DAC Write DC Servo mode complete. Bit [1] = HPOUT1R Bit [0] = HPOUT1L 1:0 DCS_STARTUP_C OMPLETE [1:0] 00 DC Servo Start-Up status 0 = Start-Up DC Servo mode not completed. 1 = Start-Up DC Servo mode complete. Bit [1] = HPOUT1R Bit [0] = HPOUT1L R89 (0059h) DC Servo Write Val 15:8 DCS_DAC_WR_VA L_1 [7:0] 00h Writing to this field sets the DC Offset value for HPOUT1R in DAC Write DC Servo mode. Reading this field gives the current DC Offset value for HPOUT1R. Two’s complement format. LSB is 0.25mV. Range is -32mV to +31.75mV 7:0 DCS_DAC_WR_VA L_0 [7:0] 00h Writing to this field sets the DC Offset value for HPOUT1L in DAC Write DC Servo mode. Reading this field gives the current DC Offset value for HPOUT1L. Two’s complement format. LSB is 0.25mV. Range is -32mV to +31.75mV Table 71 DC Servo Enable and Start-Up Modes DC SERVO ACTIVE MODES The DC Servo modes described above are suitable for initialising the DC offset correction circuit on the Headphone outputs as part of a controlled start-up sequence which is executed before the signal path is fully enabled. Additional modes are available for use whilst the signal path is active; these modes may be of benefit following a large change in signal gain, which can lead to a change in DC offset level. Periodic updates may also be desirable to remove slow drifts in DC offset caused by changes in parameters such as device temperature. The DC Servo circuit is enabled on HPOUT1L and HPOUT1R by setting DCS_ENA_CHAN_0 and DCS_ENA_CHAN_1 respectively, as described earlier in Table 71. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |