| 전자부품 데이터시트 검색엔진 |
|
L6711 데이터시트(PDF) 35 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
L6711 데이터시트(HTML) 35 Page - STMicroelectronics |
|
35 / 50 page ![]() L6711 Output voltage monitor and protections 35/50 14.5 Low side sense overcurrent (CS_SEL=OPEN) The device detects an Over Current condition for each phase when the current information IINFOx overcomes the fixed threshold of IOCTH (35µA Typ). When this happens, the device keeps the relative LS mosfet on, skipping clock cycles, until the threshold is crossed back and IINFOx results being lower than the IOCTH threshold. This implies that the device limits the bottom of each inductor current ripple. After exiting the OC condition, the LS mosfet is turned off and the HS is turned on with a duty cycle driven by the PWM comparator. Keeping the LS on, skipping clock cycles, causes the on-time subsequent to the exit from the OC condition to increase. Considering now that the device, with this kind of current sense, has maximum on-time dependence with the delivered current given by the following relationship: Where IOUT is the output current (IOUT = Σ·IPHASEx) and TSW is the switching period (TSW =1/FSW). This linear dependence has a value at zero load of 0.80 ·TSW and at maximum current of 0.40 ·TSW typical and results in two different over current behaviors of the device: 14.5.1 TON Limited output voltage. This happens when the maximum ON time is reached before that the current in each phase reaches IOCPx (IINFOx<IOCTH). Figure 17 shows the maximum output voltage that the device is able to regulate considering the TON limitation imposed by the previous relationship. If the desired output characteristic crosses the TON limited maximum output voltage, the output resulting voltage will start to drop after the crossing. In this case, the device doesn't perform constant current limitation but only limits the maximum ON time following the previous relationship. The output voltage starts to decrease follows the resulting characteristic (dotted in Figure 17) until UVP is detected or anyway until IDROOP =105µA. Figure 17. TON limited operation T ON,MAX 0.80 I D ROOP – 3.8k ⋅ () T SW = 0.80 T SW I DROOP 0 µA = ⋅ 0.40 T SW I DROOP 105 µA = ⋅ ⎩ ⎪ ⎨ ⎪ ⎧ ⋅ = 0 .8 0 ·V IN 0 .4 0 ·V IN V O U T IO U T IO C P = 3 ·IO C P x (ID R O O P = 1 0 5 µ A ) T O N L im ite dO u tp u t c h a ra c te ris tic 0 .8 0 ·V IN 0 .4 0 ·V IN V O U T IO U T IO C P = 3 ·IO C P x (ID R O O P = 1 0 5 µ A ) D e s ire dO u tp u t c h a ra c te ris tica n d U V P th re s h o ld R e s u ltin gO u tp u t c h a ra c te ris tic Maximum output Voltage b) TON Limited Output Voltage |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |