AT80SND1C-ROTIL datasheet(92/210 Pages) ATMEL

92 / 210 page

AT8xC51SND1C

4109E–8051–06/03

Isochronous Transactions

Isochronous OUT

Transactions in Standard

Mode

An endpoint should be first enabled and configured before being able to receive Isochro-

nous packets.

When an OUT packet is received on an endpoint, the RXOUTB0 bit is set by the USB

controller. This triggers an interrupt if enabled. The firmware has to select the corre

Bulk-outsponding endpoint, store the number of data Bytes by reading the UBYCTX

value is equal to 0 and no data has to be read.

The STLCRC bit in the UEPSTAX register is set by the USB controller if the packet

stored in FIFO has a corrupted CRC. This bit is updated after each new packet receipt.

When all the endpoint FIFO Bytes have been read, the firmware should clear the

RXOUTB0 bit to allow the USB controller to store the next OUT packet data into the

endpoint FIFO. Until the RXOUTB0 bit has been cleared by the firmware, the data sent

by the Host at each OUT transaction will be lost.

If the RXOUTB0 bit is cleared while the Host is sending data, the USB controller will

store only the remaining Bytes into the FIFO.

If the Host sends more Bytes than supported by the endpoint FIFO, the overflow data

won’t be stored, but the USB controller will consider that the packet is valid if the CRC is

correct.

Isochronous OUT

Transactions in Ping-pong

Mode

An endpoint should be first enabled and configured before being able to receive Isochro-

nous packets.

When a OUT packet is received on the endpoint bank 0, the RXOUTB0 bit is set by the

USB controller. This triggers an interrupt if enabled. The firmware has to select the cor-

responding endpoint, store the number of data Bytes by reading the UBYCTX register. If

the received packet is a ZLP (Zero Length Packet), the UBYCTX register value is equal

to 0 and no data has to be read.

The STLCRC bit in the UEPSTAX register is set by the USB controller if the packet

stored in FIFO has a corrupted CRC. This bit is updated after each new packet receipt.

When all the endpoint FIFO Bytes have been read, the firmware should clear the

RXOUB0 bit to allow the USB controller to store the next OUT packet data into the end-

point FIFO bank 0. This action switches the endpoint bank 0 and 1. Until the RXOUTB0

bit has been cleared by the firmware, the data sent by the Host on the bank 0 endpoint

FIFO will be lost.

If the RXOUTB0 bit is cleared while the Host is sending data on the endpoint bank 0, the

USB controller will store only the remaining Bytes into the FIFO.

When a new OUT packet is received on the endpoint bank 1, the RXOUTB1 bit is set by

the USB controller. This triggers an interrupt if enabled. The firmware empties the bank

1 endpoint FIFO before clearing the RXOUTB1 bit. Until the RXOUTB1 bit has been

cleared by the firmware, the data sent by the Host on the bank 1 endpoint FIFO will be

lost.

The RXOUTB0 and RXOUTB1 bits are alternatively set by the USB controller at each

new packet receipt.

The firmware has to clear one of these 2 bits after having read all the data FIFO to allow

a new packet to be stored in the corresponding bank.

AT80SND1C-ROTIL 데이터시트(PDF) 92 Page - ATMEL Corporation

AT80SND1C-ROTIL 데이터시트(HTML) 92 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL