HD64F2149YV datasheet(465/1075 Pages) RENESAS

465 / 1075 page

Section 15 Serial Communication Interface (SCI, IrDA)

Rev. 3.00 Jan 18, 2006 page 437 of 1044

REJ09B0280-0300

Bit 3

MPIE

Description

Multiprocessor interrupts disabled (normal reception performed)

(Initial value)

[Clearing conditions]

• When the MPIE bit is cleared to 0

• When data with MPB = 1 is received

Multiprocessor interrupts enabled*

Receive interrupt (RXI) requests, receive-error interrupt (ERI) requests, and setting

of the RDRF, FER, and ORER flags in SSR are disabled until data with the

multiprocessor bit set to 1 is received.

Note:

When receive data including MPB = 0 is received, receive data transfer from RSR to

RDR, receive error detection, and setting of the RDRF, FER, and ORER flags in SSR ,

is not performed. When receive data with MPB = 1 is received, the MPB bit in SSR is

set to 1, the MPIE bit is cleared to 0 automatically, and generation of RXI and ERI

interrupts (when the TIE and RIE bits in SCR are set to 1) and FER and ORER flag

setting is enabled.

Bit 2—Transmit End Interrupt Enable (TEIE): Enables or disables transmit-end interrupt

(TEI) request generation if there is no valid transmit data in TDR when the MSB is transmitted.

Bit 2

TEIE

Description

Transmit-end interrupt (TEI) request disabled*

(Initial value)

Transmit-end interrupt (TEI) request enabled*

Note:

TEI cancellation can be performed by reading 1 from the TDRE flag in SSR, then

clearing it to 0 and clearing the TEND flag to 0, or clearing the TEIE bit to 0.

Bits 1 and 0—Clock Enable 1 and 0 (CKE1, CKE0): These bits are used to select the SCI clock

source and enable or disable clock output from the SCK pin. The combination of the CKE1 and

CKE0 bits determines whether the SCK pin functions as an I/O port, the serial clock output pin, or

the serial clock input pin.

The setting of the CKE0 bit, however, is only valid for internal clock operation (CKE1 = 0) in

asynchronous mode. The CKE0 bit setting is invalid in synchronous mode, and in the case of

external clock operation (CKE1 = 1). The setting of bits CKE1 and CKE0 must be carried out

before the SCI’s operating mode is determined using SMR.

For details of clock source selection, see table 15.9.

HD64F2149YV 데이터시트(PDF) 465 Page - Renesas Technology Corp

HD64F2149YV 데이터시트(HTML) 465 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL