7641 datasheet(65/385 Pages) RENESAS

65 / 385 page

Rev.2.00

Aug 28, 2006

page 48 of 113

7641 Group

REJ09B0336-0200

HARDWARE

FUNCTIONAL DESCRIPTION

The USB suspend detect signal flag goes to “0” when the USB re-

sume signal detect flag (RESUME) is set to “1”. During suspend

mode, if the clock operation is started up with a process (remote

wake-up) other than the resume interrupt process (for example;

reset or timer), make sure to clear the USB suspend detect signal

flag to “0” when you set the USB remote wake-up bit to “1”. When

the USB FCU is in suspend mode and detects a non-idle signal on

the D+/D- line, the USB resume detect flag and the USB resume

signal interrupt status flag both go to “1” and a resume interrupt

request occurs. At this point, pull the internal registers (A, X, Y) in

this interrupt process routine. Take the following procedure in the

USB resume interrupt process.

(1) Set the USB line driver current control bit to “0”. (When operat-

ing at Vcc = 3.3 V, this bit does not need to be set.)

(2) Set the frequency synthesizer enable bit to “1” and set a 2 ms

to 5 ms wait.

(3) Check the frequency synthesizer lock status bit. If “0”, it must

be checked again after a 0.1 ms wait.

(4) Enable the USB clock.

Fig. 37 Structure of USB control register

USB control register (address 001316)

USBC

Reserved bit (“0” at read/write)

USB default state selection bit (USBC1)

0: In default state after power-on/reset

1: In default state after USB reset signal received

USB artificial SOF enable bit (USBC2)

0: Artificial SOF disabled

1: Artificial SOF enabled

USB line driver current control bit (USBC3)

0: High current mode

1: Low current mode

USB line driver supply enable bit (USBC4) (Note 1)

0: Line driver disabled

1: Line driver enabled

USB clock enable bit (USBC5)

0: 48 MHz clock to the USB block disabled

1: 48 MHz clock to the USB block enabled

USB SOF port select bit (USBC6)

0: SOF output disabled

1: SOF output enabled

USB enable bit (USBC7)

0: USB block disabled (Note 2)

1: USB block enabled

Notes 1: When using the MCU in Vcc = 3.3 V, set this bit to “0” and disable the built-in DC-DC converter

2: Setting this bit to 0” causes the contents of all USB registers to have the values at reset.

Set the USB resume signal interrupt status flag to “0” after the

wake-up sequence process. The USB resume detect flag goes to

“0” at the same time. When the clock operation is started up with

a remote wake-up, set the USB remote wake-up bit to “1” after the

wake-up sequence process. (keep it set to “1” for a minimum of 10

ms and maximum of 15 ms). By doing this, the MCU will send a

resume signal to the host CPU and let it know that the suspend

state has been released.

After that, set the USB remote wake-up bit and the USB suspend

detection flag to “0”, because the USB suspend detection flag is

not automatically cleared to “0” with a remote wake-up.

[USB Control Register] USBC

When using the USB function, the USB enable bit must be set to

“1”. The USB line driver supply bit must be set to “0” (DC-DC con-

verter is disabled) when operating at Vcc = 3.3V. In this condition,

the setting of the USB line driver current control bit has no effect

on USB operations.

When the USB artificial SOF enable bit is set to “1”, the MCU

judges that a SOF packet is received within 250 ns from a frame

starting if an SOF packet is destroyed owing to some cause.

7641 데이터시트(PDF) 65 Page - Renesas Technology Corp

7641 데이터시트(HTML) 65 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL