| 전자부품 데이터시트 검색엔진 |
|
MPC8641DEC 데이터시트(PDF) 21 Page - Freescale Semiconductor, Inc |
|
|
|||||||||||||||||||||||||||||
MPC8641DEC 데이터시트(HTML) 21 Page - Freescale Semiconductor, Inc |
|
21 / 140 page ![]() MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 1 Freescale Semiconductor 21 DDR and DDR2 SDRAM Table 15 provides the recommended operating conditions for the DDR SDRAM component(s) when Dn_GVDD(typ) = 2.5 V. Table 16 provides the DDR capacitance when Dn_GV DD (typ)=2.5 V. Table 17 provides the current draw characteristics for MVREF. Table 15. DDR SDRAM DC Electrical Characteristics for D n_GVDD (typ) = 2.5 V Parameter/Condition Symbol Min Max Unit Notes I/O supply voltage D n_GVDD 2.375 2.625 V 1 I/O reference voltage D n_MVREF 0.49 × Dn_GVDD 0.51 × Dn_GVDD V2 I/O termination voltage VTT D n_MVREF – 0.04 D n_MVREF + 0.04 V 3 Input high voltage VIH D n_MVREF + 0.15 D n_GVDD + 0.3 V Input low voltage VIL –0.3 D n_MVREF– 0.15 V Output leakage current IOZ –50 50 μA4 Output high current (VOUT = 1.95 V) IOH –16.2 — mA Output low current (VOUT = 0.35 V) IOL 16.2 — mA Notes: 1. D n_GVDD is expected to be within 50 mV of the DRAM Dn_GVDD at all times. 2. MVREF is expected to be equal to 0.5 × Dn_GVDD, and to track Dn_GVDD DC variations as measured at the receiver. Peak-to-peak noise on D n_MVREF may not exceed ±2% of the DC value. 3. VTT is not applied directly to the device. It is the supply to which far end signal termination is made and is expected to be equal to D n_MVREF. This rail should track variations in the DC level of Dn_MVREF. 4. Output leakage is measured with all outputs disabled, 0 V ≤ VOUT ≤ Dn_GVDD. Table 16. DDR SDRAM Capacitance for D n_GVDD (typ) = 2.5 V Parameter/Condition Symbol Min Max Unit Notes Input/output capacitance: DQ, DQS CIO 68 pF 1 Delta input/output capacitance: DQ, DQS CDIO —0.5 pF 1 Note: 1. This parameter is sampled. D n_GVDD = 2.5 V ± 0.125 V, f = 1 MHz, TA = 25°C, VOUT = Dn_GVDD/2, VOUT (peak-to-peak) = 0.2 V. Table 17. Current Draw Characteristics for MVREF Parameter / Condition Symbol Min Max Unit Note Current draw for MVREF IMVREF —500 μA1 1. The voltage regulator for MVREF must be able to supply up to 500 μA current. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |