ST72371 datasheet(63/94 Pages) STMICROELECTRONICS

63 / 94 page

63/94

ST72371/ST72372

SERIAL COMMUNICATIONS INTERFACE(Cont’d)

4.5.5 Register Description

STATUS REGISTER (SR)

Read Only

Reset Value: 1100 0000 (C0h)

Bit 7 = TDRE Transmit data register empty.

This bit is set by hardware when the content of the

TDR register has been transferred into the shift

the CR2 register. It is cleared by a software se-

quence (an access to the SR register followed by a

write to the DR register).

0: Data is not transferred to the shift register

1: Data is transferred to the shift register

Note: data will not be transferred to the shift regis-

ter as long as the TDRE bit is not reset.

Bit 6 = TC

Transmission complete.

This bit is set by hardware when transmission of a

frame containing Data, a Preamble or a Break is

complete. An interrupt is generated if TCIE=1 in

the CR2 register. It is cleared by a software se-

quence (an access to the SR register followed by a

write to the DR register).

0: Transmission is not complete

1: Transmission is complete

Bit 5 = RDRF

Received data ready flag.

This bit is set by hardware when the content of the

RDR register has been transferred into the DR

CR2 register. It is cleared by hardware when

RE=0 or by a software sequence (an access to the

SR register followed by a read to the DR register).

0: Data is not received

1: Received data is ready to be read

Bit 4 = IDLE Idle line detect.

This bit is set by hardware when a Idle Line is de-

tected. An interrupt is generated if the ILIE=1 in

the CR2 register. It is cleared by hardware when

RE=0 by a software sequence (an access to the

SR register followed by a read to the DR register).

0: No Idle Line is detected

1: Idle Line is detected

Note: The IDLE bit will not be set again until the

RDRF bit has been set itself (i.e. a new idle line oc-

curs). This bit is not set by an idle line when the re-

ceiver wakes up from wake-up mode.

Bit 3 = OR

Overrun error.

This bit is set by hardware when the word currently

being received in the shift register is ready to be

transferred into the RDR register while RDRF=1.

An interrupt is generated if RIE=1 in the CR2 reg-

ister. It is cleared by hardware when RE=0 by a

software sequence (an access to the SR register

followed by a read to the DR register).

0: No Overrun error

1: Overrun error is detected

Note: When this bit is set RDR register content will

not be lost but the shift register will be overwritten.

Bit 2 = NF

Noise flag.

This bit is set by hardware when noise is detected

on a received frame. It is cleared by hardware

when RE=0 by a software sequence (an access to

the SR register followed by a read to the DR regis-

ter).

0: No noise is detected

1: Noise is detected

Note: This bit does not generate interrupt as it ap-

pears at the same time as the RDRF bit which it-

self generates an interrupt.

Bit 1 = FE Framing error.

This bit is set by hardware when a de-synchroniza-

tion, excessive noise or a break character is de-

tected. It is cleared by hardware when RE=0 by a

software sequence (an access to the SR register

followed by a read to the DR register).

0: No Framing error is detected

1: Framing error or break character is detected

Note: This bit does not generate interrupt as it ap-

pears at the same time as the RDRF bit which it-

self generates an interrupt. If the word currently

being transferred causes both frame error and

overrun error, it will be transferred and only the OR

bit will be set.

Bit 0 = Reserved, forced by hardware to 0.

TDRE

RDRF

IDLE

ST72371 데이터시트(PDF) 63 Page - STMicroelectronics

ST72371 데이터시트(HTML) 63 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94

데이터시트 다운로드

링크 URL