STM32W108HB datasheet(74/179 Pages) STMICROELECTRONICS

74 / 179 page

Serial interfaces

STM32W108CB, STM32W108HB

74/179

Doc ID 16252 Rev 2

SC_RXSSEL

SC_RX

FRMB

SC_RX

FRMA

SC_RX

PARB

SC_RX

PARA

SC_RX

OVFB

SC_R

XOVF

SC_TX

ACTB

SC_TX

ACTA

SC_RX

ACTB

SC_RX

ACTA

[12:10] SC_RXSSEL: Status of the receive count saved in SCx_RXCNTSAVED (SPI slave

mode) when nSSEL deasserts. Cleared when a receive buffer is loaded and when

the receive DMA is reset.

0: No count was saved because nSSEL did not deassert.

2: Buffer A's count was saved, nSSEL deasserted once.

3: Buffer B's count was saved, nSSEL deasserted once.

6: Buffer A's count was saved, nSSEL deasserted more than once.

7: Buffer B's count was saved, nSSEL deasserted more than once.

1, 4, 5: Reserved.

[9] SC_RXFRMB: This bit is set when DMA receive buffer B reads a byte with a frame

error from the receive FIFO. It is cleared the next time buffer B is loaded or when the

receive DMA is reset. (SC1 in UART mode only)

[8] SC_RXFRMA: This bit is set when DMA receive buffer A reads a byte with a frame

error from the receive FIFO. It is cleared the next time buffer A is loaded or when the

receive DMA is reset. (SC1 in UART mode only)

[7] This bit is set when DMA receive buffer B reads a byte with a parity error from the

receive FIFO. It is cleared the next time buffer B is loaded or when the receive DMA

is reset. (SC1 in UART mode only)

[6] This bit is set when DMA receive buffer A reads a byte with a parity error from the

receive FIFO. It is cleared the next time buffer A is loaded or when the receive DMA

is reset. (SC1 in UART mode only)

[5] This bit is set when DMA receive buffer B was passed an overrun error from the

receive FIFO. Neither receive buffer was capable of accepting any more bytes

(unloaded), and the FIFO filled up. Buffer B was the next buffer to load, and when it

drained the FIFO the overrun error was passed up to the DMA and flagged with this

bit. Cleared the next time buffer B is loaded and when the receive DMA is reset.

[4] This bit is set when DMA receive buffer A was passed an overrun error from the

receive FIFO. Neither receive buffer was capable of accepting any more bytes

(unloaded), and the FIFO filled up. Buffer A was the next buffer to load, and when it

drained the FIFO the overrun error was passed up to the DMA and flagged with this

bit. Cleared the next time buffer A is loaded and when the receive DMA is reset.

[3] This bit is set when DMA transmit buffer B is active.

[2] This bit is set when DMA transmit buffer A is active.

[1] This bit is set when DMA receive buffer B is active.

[0] This bit is set when DMA receive buffer A is active.

STM32W108HB 데이터시트(PDF) 74 Page - STMicroelectronics

STM32W108HB 데이터시트(HTML) 74 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL