AT89LP6440 datasheet(97/194 Pages) ATMEL

97 / 194 page

3706A–MICRO–9/09

AT89LP6440 - Preliminary

In a more complex system, the following could be used to select slaves 1 and 2 while excluding

slave 0:

Slave 0

SADDR = 1100 0000

SADEN = 1111 1001

Given

= 1100 0XX0

Slave 1

SADDR = 1110 0000

SADEN = 1111 1010

Given

= 1110 0X0X

Slave 2

SADDR = 1110 0000

SADEN = 1111 1100

Given

= 1110 00XX

In the above example, the differentiation among the 3 slaves is in the lower 3 address bits. Slave

0 requires that bit 0 = 0 and it can be uniquely addressed by 1110 0110. Slave 1 requires that

bit 1 = 0 and it can be uniquely addressed by 1110 and 0101. Slave 2 requires that bit 2 = 0 and

its unique address is 1110 0011. To select Slaves 0 and 1 and exclude Slave 2, use address

1110 0100, since it is necessary to make bit 2 = 1 to exclude slave 2.

The Broadcast Address for each slave is created by taking the logic OR of SADDR and SADEN.

Zeros in this result are trended as don’t cares. In most cases, interpreting the don’t cares as

ones, the broadcast address will be FF hexadecimal.

Upon reset SADDR (SFR address 0A9H) and SADEN (SFR address 0B9H) are loaded with

“0”s. This produces a given address of all “don’t cares” as well as a Broadcast address of all

“don’t cares”. This effectively disables the Automatic Addressing mode and allows the microcon-

troller to use standard 80C51-type UART drivers which do not make use of this feature.

17. Enhanced Serial Peripheral Interface

The Serial Peripheral Interface (SPI) allows high-speed synchronous data transfer between the

AT89LP6440 and peripheral devices or between multiple AT89LP6440 devices, including multi-

ple masters and slaves on a single bus. The SPI includes the following features:

•Full-duplex, 3-wire or 4-wire Synchronous Data Transfer

•Master or Slave Operation

•Maximum Bit Frequency = f

OSC/4

•LSB First or MSB First Data Transfer

•Four Programmable Bit Rates or Timer 1-based Baud Generation (Master Mode)

•End of Transmission Interrupt Flag

• Write Collision Flag Protection

•Double-buffered Receive and Transmit

•Transmit Buffer Empty Interrupt Flag

• Mode Fault (Master Collision) Detection and Interrupt

•Wake up from Idle Mode

A block diagram of the SPI is shown below in Figure 17-1.

AT89LP6440 데이터시트(PDF) 97 Page - ATMEL Corporation

AT89LP6440 데이터시트(HTML) 97 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL