| 전자부품 데이터시트 검색엔진 |
|
AT89LP6440 데이터시트(PDF) 17 Page - ATMEL Corporation |
|
|
|||||||||||||||||||||||||||||
AT89LP6440 데이터시트(HTML) 17 Page - ATMEL Corporation |
|
17 / 194 page ![]() 17 3706A–MICRO–9/09 AT89LP6440 - Preliminary Figure 3-8 shows a hardware configuration for accessing 256-byte blocks of external RAM using an 8-bit paged address. Port 0 serves as a multiplexed address/data bus to the RAM. The ALE strobe is used to latch the address byte into an external register so that Port 0 can be freed for data input/output. The Port 2 I/O lines (or other ports) can provide control lines to page the mem- ory; however, this operation is not handled automatically by hardware. The software application must change the Port 2 register when appropriate to access different pages. The MOVX @Ri instructions use Paged Address mode. Figure 3-8. External Memory 8-bit Paged Address Mode Note that prior to using the external memory interface, Port 2, WR (P3.6), RD (P3.7) and ALE (P4.4) must be configured as outputs. See Section 10.1 “Port Configuration” on page 44. Port 0 is configured automatically to push-pull output mode when outputting address or data and is P1 P0 I/O ALE P2 RD P3 WR AT89LP DATA LATCH EXTERNAL DATA MEMORY WE ADDR PAGE BITS OE Table 3-4. AUXR – Auxiliary Control Register CLKREG = 8EH Reset Value = xxx0 0000B Not Bit Addressable –– – XSTK WS1WS0 EXRAM ALES Bit 7 6 543 21 0 Symbol Function XSTK Extended Stack Enable. When XSTK = 0 the stack resides in IDATA and is limited to 256 bytes. Set XSTK = 1 to place the stack in EDATA for up to 4K bytes of extended stack space. All PUSH, POP, CALL and RET instructions will incur a one or two cycle penalty when accessing the extended stack. WS[1-0] Wait State Select. Determines the number of wait states inserted into external memory accesses. WS1 WS0 Wait States RD / WR Strobe Width 000 1 x tCYC 011 2 x t CYC 102 3 x tCYC 113 4 x tCYC EXRAM External RAM Enable. When EXRAM = 0, MOVX instructions can access the internally mapped portions of the address space. Accesses to addresses above internally mapped memory will access external memory. Set EXRAM = 1 to bypass the internal memory and map the entire address space to external memory. ALES ALE Idle State. When ALES = 0 the idle polarity of ALE is high (active). When ALES = 1 the idle polarity of ALE is low (inactive). The ALE strobe pulse is always active high. ALES must be zero in order to use P4.4 as a general I/O. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |