| 전자부품 데이터시트 검색엔진 |
|
AT89LP6440 데이터시트(PDF) 103 Page - ATMEL Corporation |
|
|
|||||||||||||||||||||||||||||
AT89LP6440 데이터시트(HTML) 103 Page - ATMEL Corporation |
|
103 / 194 page ![]() 103 3706A–MICRO–9/09 AT89LP6440 - Preliminary 17.4 Serial Clock Timing The CPHA, CPOL and SPR bits in SPCR control the shape and rate of SCK. The two SPR bits provide four possible clock rates when the SPI is in master mode. In slave mode, the SPI will operate at the rate of the incoming SCK as long as it does not exceed the maximum bit rate. There are also four possible combinations of SCK phase and polarity with respect to the serial data. CPHA and CPOL determine which format is used for transmission. The SPI data transfer formats are shown in Figures 17-3 and 17-4. To prevent glitches on SCK from disrupting the interface, CPHA, CPOL, and SPR should not be modified while the interface is enabled, and the master device should be enabled before the slave device(s). Figure 17-3. SPI Transfer Format with CPHA = 0 Note: *Not defined but normally MSB of character just received. Figure 17-4. SPI Transfer Format with CPHA = 1 Note: *Not defined but normally LSB of previously transmitted character. SSIG Slave Select Ignore. If SSIG = 0, the SPI will only operate in slave mode if SS (P1.4) is pulled low. When SSIG = 1, the SPI ignores SS in slave mode and is active whenever SPE (SPCR.6) is set. When MSTR = 1 and SSIG = 0, SS is monitored for master mode collisions. Setting SSIG = 1 will ignore collisions on SS. P1.4 may be used as a regular I/O pin when SSIG = 1. DISSO Disable slave output bit. When set, this bit causes the MISO pin to be tristated so that more than one slave device can share the same interface without multiple SS lines. Normally, the first byte in a transmission could be the slave address and only the selected slave should clear its DISSO bit. ENH TX Buffer Interrupt Enable. When ENH = 1, TXE will generate an SPI interrupt if ESP = 1. When ENH = 0, TXE does not generate an interrupt. MSB 6 5 4 3 2 1 LSB 1 2 3 4 5 6 7 8 MSB * 65 4 3 2 1 LSB SCK CYCLE # (FOR REFERENCE) SCK (CPOL = 0) SCK (CPOL = 1) MOSI (FROM MASTER) MISO (FROM SLAVE) SS (TO SLAVE) |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |