ST7533 datasheet(30/60 Pages) SITRONIX

30 / 60 page

ST7533

Ver 1.0

30/60

2003/07/21

The Reset Circuit

When the /RES input comes to the “L” level, these LSIs

return to the default state. Their default states are as follows:

1. Display OFF

2. Normal display

3. ADC select: Normal (ADC command D0 = “L”)

4. Power control register: (D2, D1, D0) = (0, 0, 0)

5. Serial interface internal register data clear

6. LCD power supply bias rate:

1/33 DUTY = 1/6 bias

1/17 DUTY = 1/5 bias

7. All-indicator lamps-on OFF (All-indicator lamps ON/OFF

command D0 = “L”)

8. Power saving clear

9. V5 voltage regulator internal resistors Ra and Rb

separation

10. Output conditions of SEG and COM terminals

SEG=VDD , COM=VDD

11. Read modify write OFF

12. Static indicator OFF Static indicator register : (D1, D2) =

(0, 0)

13. Display start line set to first line

14. Column address set to Address 0

15. Page address set to Page 0

16. Common output status normal

17. V5 voltage regulator internal resistor ratio set mode clear

18. Electronic volume register set mode clear Electronic

volume register :

(D 5, D4, D3, D 2 , D1, D 0 ) = (1, 0. 0, 0, 0,0 )

19. Test mode clear

On the other hand, when the reset command is used, the

above default settings from 11 to 19 are only executed.

When the power is turned on, the IC internal state becomes

unstable, and it is necessary to initialize it using the /RES

terminal. After the initialization, each input terminal should

be controlled normally.

Moreover, when the control signal from the MPU is in the

high impedance, an over current may flow to the IC. After

applying a current, it is necessary to take proper measures to

prevent the input terminal from getting into the high

impedance state.

If the internal liquid crystal power supply circuit is not used on

ST7533,it is necessary that /RES is “H” when the external

liquid crystal power supply is turned on. This IC has the

function to discharge V5 when /RES is “L,” and the external

power supply short-circuits to VDD when /RES is “L.”

While /RES is “L,” the oscillator and the display timing

generator stop, and the CL, FR, FRS and /DOF terminals are

fixed to “H.” The terminals D0 to D7 are not affected. The

VDD level is output from the SEG and COM output terminals.

This means that an internal resistor is connected between

VDD and V5.

When the internal liquid crystal power supply circuit is not

used on other models of ST7533 series, it is necessary that

/RES is “L” when the external liquid crystal power supply is

turned on.

While /RES is “L,” the oscillator works but the display timing

generator stops, and the CL, FR, FRS and /DOF terminals

are fixed to “H.” The terminals D0 to D7 are not affected.

ST7533 데이터시트(PDF) 30 Page - Sitronix Technology Co., Ltd.

ST7533 데이터시트(HTML) 30 Page - Sitronix Technology Co., Ltd.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

데이터시트 다운로드

링크 URL