AS3525 datasheet(70/194 Pages) AMSCO

70 / 194 page

AS3525-A/-B C22O22

Data Sheet, Confidential

www.austriamicrosystems.com

Revision 1.13

- 194

For the relationship of the clocks following constraints must be met:

•

LRCK must change with the falling edge of MCLK while MCLK is low (constrained should be set to 40 % of the MCLK period, see figure

below).

•

SDATA must change at the falling edge of SCLK. It will be read with the rising edge of SCLK.

Figure 30 Clock constraints

I2SO_LRCK

I2SO_SCLK

I2SO_SDATA

I2SO_MCLK

L15

L14

R15

R14

Lrck must change with falling edge,

within 40 % of MCLK period

Sampling of I2S data by Cello IF with rising edge of SCLK

7.3.10.2 Power Modes

The I2SOUTIF contains two clock domains. Each clock domain can be turned off separately. The I2SO_MCLK must be turned off in the global

clock controller register. This is necessary, as the audio chip requires I2SO_MCLK and I2SO_SCLK not only for I2S output, but also I2S input (see

I2SINIF).

PCLK Idle Mode

If the PCLK is turned off (by the clock controller) the I2SOUT_STATUS register can hold invalid data. However, no interrupt should be triggered if

the I2SOUTIF is in idle mode.

I2SO_MCLK Idle Mode

If I2SO_MCLK is disabled (by the clock controller) no audio samples are read from the FIFO. The output signals remain unchanged until the

I2SO_MCLK is enabled again.

7.3.10.3 Loopback Feature

On the AS3525 are two I2S interfaces:

•

I2SOUTIF is responsible to send values to the DAC of the audio chip via I2SO_SDATA

•

I2SINIF is responsible to receive audio values from ADC of the audio chip via I2SI_SDATA

In the AS3525 both SDATA signals are provided as loopback signals (I2SO_FSDATA, I2SI_FSDATA):

•

I2SO_SDATA to I2SINIF: This loopback is mainly for testing the transmission and reception paths of both I2S interfaces.

The loopback signal is called I2SO_FSDATA.

•

I2SI_SDATA to I2SOUTIF: This loopback feature allows the application to echo the input audio samples directly to a

loudspeaker. The signal provided by the I2SINIF is called I2SI_FSDATA.

In normal mode the I2SOUTIF generates the I2SO_SDATA signal based on the contents of the FIFO. If the loop back feature is enabled, the

SDATA_LB bit in the I2SOUT_CONTROL register must be set.

NOTE: This feature will only be available if SCLK is the same for I2S input and output interface. For implementation the I2SI_FSDATA signal is

simply routed through a multiplexer to the I2SO_SDATA interface.

AS3525 데이터시트(PDF) 70 Page - ams AG

AS3525 데이터시트(HTML) 70 Page - ams AG

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL