| 전자부품 데이터시트 검색엔진 |
|
S5000PAL 데이터시트(PDF) 72 Page - Intel Corporation |
|
|
|||||||||||||||||||||||||||||
S5000PAL 데이터시트(HTML) 72 Page - Intel Corporation |
|
72 / 112 page ![]() Intel ® Server Board S5000PAL / S5000XAL TPS Power and Environmental Specifications Revision 1.7 Intel order number: D31979-010 73 8.2.8 Dynamic Loading The output voltages shall remain within limits for the step loading and capacitive loading specified in the table below. The load transient repetition rate shall be tested between 50 Hz and 5 kHz at duty cycles ranging from 10%-90%. The load transient repetition rate is only a test specification. The Δ step load may occur anywhere within the MIN load to the MAX load conditions. Table 38. Transient Load Requirements Output Δ Step Load Size (See note 2) Load Slew Rate Test capacitive Load +3.3V 5.0A 0.25 A/ μsec 250 μF +5V 6.0A 0.25 A/ μsec 400 μF 12V1+12V2+12V3+12 V4 28.0A 0.25 A/ μsec 2200 μF 1,2 +5VSB 0.5A 0.25 A/ μsec 20 μF Notes: 1) Step loads on each 12V output may happen simultaneously. 2) The +12V should be tested with 2200 μF evenly split between the four +12V rails. 8.2.9 Capacitive Loading The power supply shall be stable and meet all requirements with the following capacitive loading ranges. Table 39. Capacitive Loading Conditions Output MIN MAX Units +3.3V 250 6,800 μF +5V 400 4,700 μF +12V1,2,3,4 500 each 11,000 μF -12V 1 350 μF +5VSB 20 350 μF 8.2.10 Closed-Loop Stability The power supply shall be unconditionally stable under all line/load/transient load conditions including capacitive load ranges. A minimum of: 45 degrees phase margin and -10dB-gain margin is required. Closed-loop stability must be ensured at the maximum and minimum loads as applicable. 8.2.11 Common Mode Noise The common mode noise on any output shall not exceed 350 mV pk-pk over the frequency band of 10Hz to 30MHz. 1. The measurement shall be made across a 100 Ω resistor between each of the DC outputs, including ground, at the DC power connector and chassis ground (power subsystem enclosure). 2. The test set-up shall use an FET probe such as Tektronix* model P6046 or equivalent. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |