AD9557SLASHPCBZ datasheet(83/92 Pages) AD

83 / 92 page

Data Sheet

AD9557

Rev. A | Page 83 of 92

Address

Bits

Bit Name

Description

0x0C06

[7:5]

Reserved

Sel high PM base

loop filter

0 = base loop filter with normal (70°) phase margin (default).

1 = base loop filter with high (88.5°) phase margin.

(<0.1 dB peaking in closed-loop transfer function).

[3:2]

DPLL loop BW

Scales the DPLL loop BW while in soft pin mode.

00 (default) = 50 Hz.

01 = 1 Hz.

10 = 10 Hz.

11 = 100 Hz.

[1:0]

Reference input

frequency tolerance

Scales the input frequency tolerance while in soft pin mode.

00 (default) = outer tolerance: 10%; inner tolerance: 8% (for general conditions).

01 = outer tolerance: 12 ppm; inner tolerance: 9.6 ppm (for Stratum 3).

10 = outer tolerance: 48 ppm; inner tolerance: 38 ppm (for SMC clock standard).

11 = outer tolerance: 200 ppm; inner tolerance: 160 ppm (for XTAL system clock).

[7:1]

Reserved

Reserved.

0x0C07

Soft pin start transfer

Autoclearing register. 1 = initiates ROM download without resetting the part/register map.

After ROM download is complete, this register is reset.

[7:1]

Reserved

Reserved.

0x0C08

Soft pin reset

Autoclearing register; resets the part like soft reset (Register 0x0000[5]), except that this reset

function initiates a soft pin ROM download without resetting the part/register map. After ROM

download is complete, this register is pulled back to zero.

STATUS READBACK (REGISTER 0x0D00 TO REGISTER 0x0D14)

All bits in Register 0x0D00 to Register 0x0D14 are read only. To show the latest status, these registers require an I/O update (Register 0x0005 =

0x01) immediately before being read.

Table 98. EEPROM Status

Address

Bits

Bit Name

Description

[7:4]

Reserved

Reserved.

Pin program ROM

load process

The control logic sets this bit when data is being read from the ROM.

Fault detected

An error occurred while saving data to or loading data from the EEPROM.

Load in progress

The control logic sets this bit while data is being read from the EEPROM.

0x0D00

Save in progress

The control logic sets this bit while data is being written to the EEPROM.

Table 99. SYSCLK Status

Address

Bits

Bit Name

Description

Reserved

Reserved.

DPLL_APLL_Lock

Indicates the status of the DPLL and APLL.

0 = either the DPLL or the APLL is unlocked.

1 = both the DPLL and APLL are locked.

All PLLs locked

Indicates the status of the system clock PLL, APLL, and DPLL.

0 = system clock PLL or APLL or DPLL is unlocked.

1 = all three PLLs (system clock PLL, APLL, and DPLL) are locked.

APLL VCO status

1 = OK.

0 = off/clocks are missing.

APLL cal in process

The control logic holds this bit set while the amplitude calibration of the APLL VCO is in progress.

APLL lock

Indicates the status of the APLL.

0 = unlocked.

1 = locked.

System clock stable

The control logic sets this bit when the device considers the system clock to be stable (see the

System Clock Stability Timer section).

0 = not stable (the system clock stability timer has not expired yet).

1 = stable (the system clock stability timer has expired).

0x0D01

SYSCLK lock detect

Indicates the status of the system clock PLL.

0 = unlocked.

1 = locked.

AD9557/PCBZ 데이터시트(PDF) 83 Page - Analog Devices

AD9557/PCBZ 데이터시트(HTML) 83 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92

데이터시트 다운로드

링크 URL