PIC16F883-ESLASHSO. datasheet(190/338 Pages) MICROCHIP

190 / 338 page

PIC16F882/883/884/886/887

DS41291G-page 190

 2006-2012 Microchip Technology Inc.

13.3.4

SLAVE MODE

In Slave mode, the data is transmitted and received as

the external clock pulses appear on SCK. When the

last bit is latched, the SSPIF interrupt flag bit of the

PIR1 register is set.

While in Slave mode, the external clock is supplied by

the external clock source on the SCK pin. This external

clock must meet the minimum high and low times, as

specified in the electrical specifications.

While in Sleep mode, the slave can transmit/receive

data. When a byte is received, the device will wake-up

from Sleep.

13.3.5

SLAVE SELECT

SYNCHRONIZATION

The SS pin allows a Synchronous Slave mode. The

SPI must be in Slave mode with SS pin control

enabled (SSPCON<3:0> = 04h). The pin must not

be driven low for the SS pin to function as an input.

The Data Latch must be high. When the SS pin is

low, transmission and reception are enabled and

the SDO pin is driven. When the SS pin goes high,

the SDO pin is no longer driven, even if in the mid-

dle of a transmitted byte, and becomes a floating

output. External pull-up/pull-down resistors may be

desirable, depending on the application.

When the SPI module resets, the bit counter is forced

to ‘0’. This can be done by either forcing the SS pin to

a high level, or clearing the SSPEN bit.

To emulate two-wire communication, the SDO pin can

be connected to the SDI pin. When the SPI needs to

operate as a receiver, the SDO pin can be configured

as an input. This disables transmissions from the SDO.

The SDI can always be left as an input (SDI function),

since it cannot create a bus conflict.

FIGURE 13-3:

SLAVE SYNCHRONIZATION WAVEFORM

Note 1: When the SPI is in Slave mode with SS

pin control enabled (SSPCON<3:0> =

0100), the SPI module will reset if the SS

pin is set to VDD.

2: If the SPI is used in Slave mode with CKE

set (SSPSTAT register), then the SS pin

control must be enabled.

SCK

(CKP = 1

SCK

(CKP = 0

Input

Sample

SDI

bit 7

SDO

bit 7

bit 6

bit 7

SSPIF

(SMP = 0)

CKE = 0)

(SMP = 0)

Write to

SSPBUF

SSPSR to

SSPBUF

bit 0

bit 7

bit 0

Next Q4 Cycle

after Q2



PIC16F883-E/SO. 데이터시트(PDF) 190 Page - Microchip Technology

PIC16F883-E/SO. 데이터시트(HTML) 190 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL