PIC16F883-ESLASHSO. datasheet(193/338 Pages) MICROCHIP

193 / 338 page

 2006-2012 Microchip Technology Inc.

DS41291G-page 193

PIC16F882/883/884/886/887

13.4

MSSP I2C Operation

The MSSP module in I2C mode, fully implements all

master and slave functions (including general call

support) and provides interrupts on Start and Stop bits in

hardware, to determine a free bus (Multi-Master mode).

The MSSP module implements the standard mode

specifications, as well as 7-bit and 10-bit addressing.

Two pins are used for data transfer. These are the

RC3/SCK/SCL pin, which is the clock (SCL), and the

RC4/SDI/SDA pin, which is the data (SDA). The user

must configure these pins as inputs or outputs through

the TRISC<4:3> bits.

The MSSP module functions are enabled by setting

MSSP Enable bit SSPEN of the SSPCON register.

FIGURE 13-6:

MSSP BLOCK DIAGRAM

(I2C MODE)

The MSSP module has these six registers for I2C

operation:

• MSSP Control Register 1 (SSPCON)

• MSSP Control Register 2 (SSPCON2)

• MSSP STATUS register (SSPSTAT)

• Serial Receive/Transmit Buffer (SSPBUF)

• MSSP Shift Register (SSPSR) – Not directly

accessible

• MSSP Address register (SSPADD)

• MSSP Mask register (SSPMSK)

The SSPCON register allows control of the I2C

operation. The SSPM<3:0> mode selection bits

(SSPCON register) allow one of the following I2C modes

to be selected:

•I2C Master mode, clock = OSC/4 (SSPADD +1)

•I2C Slave mode (7-bit address)

•I2C Slave mode (10-bit address)

•I2C Slave mode (7-bit address), with Start and

Stop bit interrupts enabled

•I2C Slave mode (10-bit address), with Start and

Stop bit interrupts enabled

•I2C firmware controlled master operation, slave is

idle

Selection of any I2C mode with the SSPEN bit set,

forces the SCL and SDA pins to be open drain,

provided these pins are programmed to be inputs by

setting the appropriate TRISC bits.

13.4.1

SLAVE MODE

In Slave mode, the SCL and SDA pins must be

configured as inputs (TRISC<4:3> set). The MSSP

module will override the input state with the output data

when required (slave-transmitter).

When an address is matched, or the data transfer after

an address match is received, the hardware

automatically will generate the Acknowledge (ACK)

pulse and load the SSPBUF register with the received

value currently in the SSPSR register.

If either or both of the following conditions are true, the

MSSP module will not give this ACK pulse:

a) The buffer full bit BF (SSPCON register) was set

before the transfer was received.

b) The overflow bit SSPOV (SSPCON register)

was set before the transfer was received.

In this event, the SSPSR register value is not loaded

into the SSPBUF, but bit SSPIF of the PIR1 register is

set. The BF bit is cleared by reading the SSPBUF

The SCL clock input must have a minimum high and

low for proper operation. The high and low times of the

I2C specification, as well as the requirement of the

MSSP module, are shown in timing parameter #100

and parameter #101.

Read

Write

SSPSR Reg

Match Detect

SSPADD Reg

Start and

Stop bit Detect

SSPBUF Reg

Internal

Data Bus

Addr Match

Set, Reset

S, P bits

(SSPSTAT Reg)

RC3/SCK/SCL

RC4/

Shift

Clock

MSb

SDI/

LSb

SDA

Note: I/O pins have diode protection to VDD and VSS.

SSPMSK Reg

PIC16F883-E/SO. 데이터시트(PDF) 193 Page - Microchip Technology

PIC16F883-E/SO. 데이터시트(HTML) 193 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL