PIC16C54T-HSSLASHSS datasheet(30/217 Pages) MICROCHIP

30 / 217 page

PIC16C5X

DS30453B-page 30

Preliminary

6.2

Prescaler

An 8-bit counter is available as a prescaler for the

Timer0 module, or as a postscaler for the Watchdog

Timer (WDT) (WDT postscaler not implemented on

PIC16C52), respectively (Section 6.1.2). For simplicity,

this counter is being referred to as “prescaler”

throughout this data sheet. Note that the prescaler

may be used by either the Timer0 module or the WDT,

but not both. Thus, a prescaler assignment for the

Timer0 module means that there is no prescaler for

the WDT, and vice-versa.

The PSA and PS2:PS0 bits (OPTION<3:0>) determine

prescaler assignment and prescale ratio.

When assigned to the Timer0 module, all instructions

writing to the TMR0 register (e.g., CLRF 1, MOVWF 1,

BSF 1,x,

etc.) will clear the prescaler. When assigned

to WDT, a CLRWDT instruction will clear the prescaler

along with the WDT. The prescaler is neither readable

nor writable. On a RESET, the prescaler contains all

'0's.

6.2.1

SWITCHING PRESCALER ASSIGNMENT

The prescaler assignment is fully under software control

(i.e., it can be changed “on the ﬂy” during program

execution). To avoid an unintended device RESET, the

following instruction sequence (Example 6-1) must be

executed when changing the prescaler assignment from

Timer0 to the WDT.

EXAMPLE 6-1:

CHANGING PRESCALER

(TIMER0

→WDT)

1.CLRWDT

;Clear WDT

2.CLRF

TMR0

;Clear TMR0 & Prescaler

3.MOVLW

'00xx1111’b

;These 3 lines (5, 6, 7)

4.OPTION

; are required only if

; desired

5.CLRWDT

;PS<2:0> are 000 or 001

6.MOVLW

'00xx1xxx’b

;Set Postscaler to

7.OPTION

; desired WDT rate

To change prescaler from the WDT to the Timer0

module, use the sequence shown in Example 6-2. This

sequence must be used even if the WDT is disabled. A

CLRWDT

instruction should be executed before switching

the prescaler.

EXAMPLE 6-2:

CHANGING PRESCALER

(WDT

→TIMER0)

CLRWDT

;Clear WDT and

;prescaler

MOVLW

'xxxx0xxx'

;Select TMR0, new

;prescale value and

;clock source

OPTION

FIGURE 6-6:

BLOCK DIAGRAM OF THE TIMER0/WDT PRESCALER

T0CKI

T0SE

TCY ( = Fosc/4)

Sync

Cycles

TMR0 reg

8-bit Prescaler

8 - to - 1MUX

MUX

Watchdog

Timer

PSA

WDT

Time-Out

PS2:PS0

Note: T0CS, T0SE, PSA, PS2:PS0 are bits in the OPTION register.

PSA

WDT Enable bit

Data Bus

PSA

T0CS

WDT not implemented on PIC16C52.

PIC16C54T-HS/SS 데이터시트(PDF) 30 Page - Microchip Technology

PIC16C54T-HS/SS 데이터시트(HTML) 30 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL