MEC1322 datasheet(283/456 Pages) MICROCHIP

283 / 456 page

 2014 - 2015 Microchip Technology Inc.

DS00001719D-page 283

MEC1322

24.11.2

TACHX STATUS REGISTER

Note 1:

Some fans offer a Locked Rotor output pin that generates a level event if a locked rotor is detected. This bit

may be used in combination with the Tach pin status bit to detect a locked rotor signal event from a fan.

Tach Input may come up as active for Locked Rotor events. This would not cause an interrupt event because

the pin would not toggle. Firmware must read the status events as part of the initialization process, if polling

is not implemented.

Offset

04h

Bits

Description

Type

Default

Reset

Event

31:4 Reserved

3 COUNT_READY_STATUS

This status bit is asserted when the Tach input changes state and

when the counter value is latched. This bit remains cleared to '0'

when the TACH_READING_MODE_SELECT bit in the TACHx Con-

trol Register is '0'.

When the TACH_READING_MODE_SELECT bit in the TACHx Con-

trol Register is set to '1', this bit is set to ‘1’ when the counter value is

latched by the hardware. It is cleared when written with a ‘1’. If

COUNT_READY_INT_EN in the TACHx Control Register is set to 1,

this status bit will assert the Tach Interrupt signal.

1=Reading ready

0=Reading not ready

R/WC

VCC1_R

ESET

2 TOGGLE_STATUS

This bit is set when Tach Input changes state. It is cleared when writ-

ten with a ’1’. If TACH_INPUT_INT_EN in the TACHx Control Regis-

ter is set to ’1’, this status bit will assert the Tach Interrupt signal.

1=Tach Input changed state (this bit is set on a low-to-high or high-to-

low transition)

0=Tach stable

R/WC

VCC1_R

ESET

1 TACH_PIN_STATUS

This bit reflects the state of Tach Input. This bit is a read only bit that

may be polled by the embedded controller.

1= Tach Input is high

0= Tach Input is low

R0b

VCC1_R

ESET

0 TACH_OUT_OF_LIMIT_STATUS

This bit is set when the Tach Count value is greater than the high

limit or less than the low limit. It is cleared when written with a ’1’. To

disable this status event set the limits to their extreme values. If

TACH_OUT_OF_LIMIT_ENABLE in the TACHx Control Register is

set to 1’, this status bit will assert the Tach Interrupt signal.

1=Tach is outside of limits

0=Tach is within limits

R/WC

VCC1_R

ESET

MEC1322 데이터시트(PDF) 283 Page - Microchip Technology

MEC1322 데이터시트(HTML) 283 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL