SST49LF016C datasheet(12/43 Pages) MICROCHIP

12 / 43 page

DS20005029B

02/16

16 Mbit LPC Serial Flash

SST49LF016C

EOL Data Sheet

Firmware Memory Cycles

Firmware Memory Read Cycle

Figure 6: Firmware Memory Read Cycle Waveform

Table 4: Firmware Memory Read Cycle Field Definitions

Clock

Cycle

Field

Name

Field

Contents

LAD[3:0]1

1. Field contents are valid on the rising edge of the present clock cycle.

LAD[3:0]

Direction

Comments

START

1101

LFRAME# must be active (low) for the part to respond. Only the last

start field (before LFRAME# transitions high) will be recognized. The

START field contents (1101b) indicate a Firmware Memory Read

cycle.

IDSEL

0000 to

1111

Indicates which SST49LF016C device should respond. If the

IDSEL (ID select) field matches the value of ID[3:0], then that par-

ticular device will respond to the LPC bus cycle.

3-9

MADD

YYYY

These seven clock cycles make up the 28-bit memory address.

YYYY is one nibble of the entire address. Addresses are trans-

ferred most-significant nibble first.

MSIZE

KKKK

The MSIZE field indicates how many bytes will be transferred

during multi-byte operations.

Device will execute multi-byte read of 2MSIZE bytes. SST49LF016C

supports only MSIZE = 0, 1, 2, 4, 7 (1, 2, 4, 16, 128 Bytes), with

KKKK=0000b, 0001b, 0010b, 0100b, or 0111b.

TAR0

1111

IN,

then Float

In this clock cycle, the master has driven the bus to all ‘1’s and then

floats the bus, prior to the next clock cycle. This is the first part of the

bus “turnaround cycle.”

TAR1

1111 (float)

Float,

then OUT

The SST49LF016C takes control of the bus during this cycle.

RSYN

0000

(READY)

OUT

During this clock cycle, the device generates a “ready sync”

(RSYNC) indicating that the device has received the input data.

The least-significant nibble of the least-significant byte will be

available during the next clock cycle.

14-A

DATA

ZZZZ

OUT

A=(13+2n+1); n = MSIZE. Least significant nibbles outputs first.

(A+1)

TAR0

1111

OUT,

then Float

In this clock cycle, the SST49LF016C drives the bus to all ones

and then floats the bus prior to the next clock cycle. This is the first

part of the bus “turnaround cycle.” A=(13+2n+1); n = MSIZE

(A+2)

TAR1

1111 (float)

Float,

then IN

The host resumes control of the bus during this cycle.

A=(13+2n+1); n = MSIZE

T4.0 20005029

1237 F03.0

LFRAME#

LAD[3:0]

1101b

0000b

A[23:20] A[19:16]

A[3:0]

A[7:4]

A[11:8]

A[15:12]

MADDR

Start

IDSEL

MSIZE

LCLK

A[27:24]

0000b

RSYNC

TAR1

TAR0

TAR

D0[7:4]

Tri-State

D0[3:0]

Dn[7:4]

Dn[3:0]

KKKKb

1111b

DATA

SST49LF016C 데이터시트(PDF) 12 Page - Microchip Technology

SST49LF016C 데이터시트(HTML) 12 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43

데이터시트 다운로드

링크 URL