전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

Preview PDF HTML

L9301 데이터시트(PDF) 13 Page - STMicroelectronics

부품명 L9301
상세설명  Automotive octal low side driver or quad low side plus quad high side driver
PDF  51 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  STMICROELECTRONICS [STMicroelectronics]
홈페이지  http://www.st.com
Logo STMICROELECTRONICS - STMicroelectronics

L9301 데이터시트(HTML) 13 Page - STMicroelectronics

Back Button L9301 Datasheet HTML 9Page - STMicroelectronics L9301 Datasheet HTML 10Page - STMicroelectronics L9301 Datasheet HTML 11Page - STMicroelectronics L9301 Datasheet HTML 12Page - STMicroelectronics L9301 Datasheet HTML 13Page - STMicroelectronics L9301 Datasheet HTML 14Page - STMicroelectronics L9301 Datasheet HTML 15Page - STMicroelectronics L9301 Datasheet HTML 16Page - STMicroelectronics L9301 Datasheet HTML 17Page - STMicroelectronics Next Button
Zoom Inzoom in Zoom Outzoom out
 13 / 51 page
background image
DocID028688 Rev 6
13/51
L9301
Discrete inputs
50
5
Discrete inputs
5.1
Output enable EN
The EN pin is the general output enable which allows the μC to immediately switch off the
output in case of need. Output driving is allowed only if this pin is driven to high level. The
device configuration can be changed only with EN pin driven to low level.
An internal pull down is present on the pin.
5.2
Output enable input IN1 to IN8
These inputs allow the outputs, depending on the configuration selected, to be enabled
without the use of the SPI. The SPI command and the IN1-8 input are logically OR'd
together.
A logic ‘1’ on this input will enable the correspondent output no matter what the status of the
SPI command register is. A logic ‘0’ on this input will disable this output if the SPI command
register is not commanding this output on. These pins can be left ‘open’ if the internal power
stages are controlled only via the SPI. This input has a nominal 100 kΩ pull down resistor to
GND, which will pull this pin to ground if an open circuit condition occurs. This input is ideally
suited for loads that are pulse width modulated (PWM'd). This allows PWM control without
the use of the SPI inputs.
Table 10. Output enable input IN1 to IN8
EN
RESET
INx
OUTx/DRNx/SRCx
X
0
X
OFF
0
X
X
OFF
1
1
0
OFF
11
1
ON



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com