PC87366 datasheet(85/240 Pages) NSC

85 / 240 page

3.0 System Wake-Up Control (SWC) (Continued)

www.national.com

3.3.8

Module IRQ Wake-Up Event

A module IRQ wake-up event is defined as the leading edge of the IRQ assertion of any of the following logical devices:

FDC, Parallel Port, Serial Ports 1 and 2, Mouse, KBC, ACB,Fan Speed Control and Monitor (FSCM), Game Port and MIDI

Port.

To enable the IRQ of a specific logical device to trigger a wake-up event, the associated Enable bit must be set to 1. This

is bit 4 of the Interrupt Number and Wake-Up on IRQ Enable register, located at index 70h in the configuration space of the

logical device (see Table 10 in

Device Architecture and Configuration chapter). When this bit is set, any IRQ assertion of the

corresponding logical device activates the module IRQ wake-up event. Therefore, the module IRQ wake-up event is a com-

bination of all IRQ signals of the logical devices for which wake-up on IRQ is enabled.

When the event is detected as active, its associated Status bit (bit 7 of the WK0_STS register) is set to 1. If the associated

Enable bit (bit 7 of the WK_EN0 register) is also set to 1, the PWUREQ output is asserted. It remains asserted until the

Status bit is cleared.

Since all the logical devices listed above are powered by VDD, a module IRQ event can be activated only when VDD is

present.

3.4

SWC REGISTERS

The SWC registers are organized in four banks, all of which are battery-backed. The offsets are related to a base address

that is determined by the SWC Base Address register in the device configuration registers. The lower 19 offsets are common

to the four banks, while the upper offsets (13-1fh) are divided as follows:

Bank 0 holds the Keyboard/Mouse Control registers.

Bank 1 holds the CEIR Control registers.

Bank 2 holds the Event Routing Conﬁguration and Wake-Up Extension Control registers.

Bank 3 holds the Standby General-Purpose I/O (GPIO) Pins Conﬁguration registers.

The active bank is selected through the Configuration Bank Select field (bits 1-0) in the Wake-Up Configuration register

(WK_CFG). See Section 3.4.6.

As a programming aid, the registers are described in this chapter according to the following functional groupings:

General status, enable, conﬁguration and routing registers

Extension enable registers

PS/2 event conﬁguration registers

CEIR event conﬁguration registers

Standby GPIO conﬁguration and control registers

The following abbreviations are used to indicate the Register Type:

R/W = Read/Write

R = Read from a speciﬁc address returns the value of a speciﬁc register. Write to the same address is to a different

W=Write

RO = Read Only

R/W1C = Read/Write 1 to Clear. Writing 1 to a bit clears it to 0. Writing 0 has no effect.

3.4.1

SWC Register Map

The following tables list the SWC registers. For the SWC register bitmap, see Section 3.5.

Table 38. Banks 0, 1, 2 and 3 - The Common Control and Status Register Map

Offset

Mnemonic

Type

Section

00h

WK_STS0

Wake-Up Events Status 0

R/W1C

3.4.2

01h

WK_STS1

Wake-Up Events Status 1

R/W1C

3.4.3

02h

WK_EN0

Wake-Up Enable 0

R/W

3.4.4

03h

WK_EN1

Wake-Up Enable 1

R/W

3.4.5

04h

WK_CFG

Wake-Up Conﬁguration

R/W

3.4.6

05h-07h

Reserved

08h

SB_GPDO0

Standby GPIOE/GPIE Data Out 0

R/W

3.4.33

PC87366 데이터시트(PDF) 85 Page - National Semiconductor (TI)

PC87366 데이터시트(HTML) 85 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL