PIC12CE673-04SLASHP datasheet(85/116 Pages) MICROCHIP

85 / 116 page

Preliminary

DS40181B-page 85

PIC12CE67X

12.3

DC Characteristics:

PIC12CE673-04 (Commercial, Industrial, Extended(4))

PIC12CE673-10 (Commercial, Industrial, Extended(4))

PIC12CE674-04 (Commercial, Industrial, Extended(4))

PIC12CE674-10 (Commercial, Industrial, Extended(4))

DC CHARACTERISTICS

Standard Operating Conditions (unless otherwise speciﬁed)

Operating temperature

0˚C

≤ TA ≤ +70˚C (commercial)

–40˚C

≤ TA ≤ +85˚C (industrial)

–40

°C ≤ TA ≤ +125˚C (extended)

Operating voltage VDD range as described in DC spec Section 12.1 and

Section 12.2.

Param

No.

Characteristic

Sym

Min

Typ

†

Max

Units

Conditions

Input Low Voltage

I/O ports

VIL

D030

with TTL buffer

VSS

0.5V

D031

with Schmitt Trigger buffer

VSS

0.2VDD

D032

MCLR, GP2/T0CKI/AN2/INT

(in EXTRC mode)

VSS

0.2VDD

D033

OSC1 (in XT, HS and LP)

VSS

0.3VDD

Note1

Input High Voltage

I/O ports

VIH

D040

with TTL buffer

2.0

VDD

4.5

≤ VDD ≤ 5.5V

D040A

0.8VDD

VDD

For VDD > 5.5V or VDD < 4.5V

D041

with Schmitt Trigger buffer

0.8VDD

VDD

For entire VDD range

D042

MCLR, GP2/T0CKI/AN2/INT

0.8VDD

VDD

D042A

OSC1 (XT, HS and LP)

0.7VDD

VDD

Note1

D043

OSC1 (in EXTRC mode)

0.9VDD

VDD

D070

GPIO weak pull-up current

IPUR

250

400

µA VDD = 5V, VPIN = VSS

Input Leakage Current (Notes 2, 3)

D060

I/O ports

IIL

µA Vss ≤ VPIN ≤ VDD, Pin at hi-

impedance

D061

MCLR, GP2/T0CKI

+5(5)

µA Vss ≤ VPIN ≤ VDD

D063

OSC1

µA Vss ≤ VPIN ≤ VDD, XT, HS and LP

osc conﬁguration

Output Low Voltage

D080

I/O ports/CLKOUT

VOL

0.6

IOL = 8.5 mA, VDD = 4.5V,

–40

°C to +85°C

D080A

0.6

IOL = 7.0 mA, VDD = 4.5V,

–40

°C to +125°C

D083

OSC2

0.6

IOL = 1.6 mA, VDD = 4.5V,

–40

°C to +85°C

D083A

0.6

IOL = 1.2 mA, VDD = 4.5V,

–40

°C to +125°C

†

Data in “Typ” column is at 5V, 25

°C unless otherwise stated. These parameters are for design guidance only

and are not tested.

Note 1: In EXTRC oscillator conﬁguration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that

the PIC12C67X be driven with external clock in RC mode.

2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The speciﬁed levels

represent normal operating conditions. Higher leakage current may be measured at different input voltages.

3: Negative current is deﬁned as coming out of the pin.

4: Extended operating range is Advance Information for this device.

5: When conﬁgured as external reset, the input leakage current is the weak pulll-up current of -10mA minimum.

This pull-up is weaker than the standard I/O pull-up.

PIC12CE673-04/P 데이터시트(PDF) 85 Page - Microchip Technology

PIC12CE673-04/P 데이터시트(HTML) 85 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL