| 전자부품 데이터시트 검색엔진 |
|
CS5530A 데이터시트(PDF) 139 Page - Advanced Micro Devices |
|
|
|||||||||||||||||||||||||||||
CS5530A 데이터시트(HTML) 139 Page - Advanced Micro Devices |
|
139 / 259 page ![]() AMD Geode™ CS5530A Companion Device Data Book 139 Display Subsystem Extensions Revision 1.1 4.8.5 Display Interface The CS5530A interfaces directly to a variety of display devices including conventional analog CRT displays, TFT flat panels, or optionally to digital NTSC/PAL encoder devices. 4.8.5.1 Video DACs The CS5530A incorporates three 8-bit video Digital-to-Ana- log Converters (DACs) for interfacing directly to CRT dis- plays. The video DACs meet the VESA specification and are capable of operation up to 157.5 MHz for supporting up to 1280x1024 display at a 85 Hz refresh rate and are VESA compliant. 4.8.5.2 VESA DDC2B / DPMS The CS5530A supports the VESA DDC2B and DPMS standards for enhanced monitor communications and power management support. 4.8.5.3 Flat Panel Support The CS5530A also interfaces directly to industry standard 18-bit Active Matrix Thin-Film-Transistor (TFT) flat panels. The CS5530A includes 24-bit to 18-bit dithering logic to increase the apparent number of colors displayed on 18-bit flat panels. In addition, the CS5530A incorporates power sequencing logic to simplify the design of a portable system. If flat panel support is not required, the flat panel output port may be used to supply digital video data to one of sev- eral types of NTSC/PAL encoder devices on the market. Flat Panel Power-Up/Down Sequence When the Flat Panel Power Enable bit (F4BAR+Memory Offset 04h[6]) transitions from a 0 to 1, the FP_ENA_VDD signal is enabled. This is followed by the data bus (includ- ing syncs and ENA_DISP). Finally, FP_ENA_BKL is enabled. The time between each of these successive stages is set by the value of the Power Sequence Delay bits (F4BAR+Memory Offset 04h[19:17]). The value in these bits refer to the number of graphics frames that will elapse between each successive enabling of the TFT sig- nals. For example, if the Power Sequence Delay is set to 3h (011b), then three frame times will elapse between the time when FP_ENA_VDD is transitioned and the data bus is transitioned. Likewise, three frame times will elapse between the data bus getting enabled and the FP_ENA_BKL is transitioned. If the panel is being refreshed at 100 Hz, each frame lasts 1 ms. So, if the Power Sequence Delay is set to 3, 3 ms will elapse between transitions. When powering off the panel, the sig- nals are transitioned in the opposite order (FP_ENA_BKL, data bus, FP_ENA_VDD) using the same Power Sequence Delay in the power-down sequence. 3 DAC Blank Enable: This bit enables the blank to the video DACs. 0 = DACs are constantly blanked; 1 = DACs are blanked normally. 2 CRT Vertical Sync Enable: Enables the CRT vertical sync. Used for VESA DPMS support. 0 = Disable; 1 = Enable. 1 CRT Horizontal Sync Enable: Enables the CRT horizontal sync. Used for VESA DPMS support. 0 = Disable; 1 = Enable. 0 Display Enable: Enables the graphics display pipeline. It is used as a reset for the display control logic. 0 = Reset display control logic; 1 = Enable display control logic. Table 4-76. Display Configuration Register (Continued) Bit Description |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |