MMPF0100Z datasheet(87/128 Pages) NXP

87 / 128 page

NXP Semiconductors

PF0100Z

FUNCTIONAL BLOCK REQUIREMENTS AND BEHAVIORS

6.4.6.5.5

VGEN5

VGEN4 AC and transient (continued)

VGEN4LITR

Transient line response

IGEN4 = 262.5 mA

VIN2INITIAL = 2.8 V to VIN2FINAL = 3.3 V for

VGEN4[3:0] = 0000 to 0111

VIN2INITIAL = VGEN4+0.3 V to VIN2FINAL = VGEN4+0.8 V for

VGEN4[3:0] = 1000 to 1010

VIN2INITIAL = VGEN4+0.25 V to VIN2FINAL = 3.6 V for

VGEN4[3:0] = 1011 to 1111

Refer to Figure 25

–5.0

8.0

Notes

67.

When the LDO output voltage is set above 2.6 V, the minimum allowed input voltage need to be at least the output voltage plus 0.25 V for proper

regulation due to the dropout voltage generated through the internal LDO transistor.

68.

The PSRR of the regulators is measured with the perturbing signal at the input of the regulator. The power management IC is supplied separately

from the input of the regulator and does not contain the perturbed signal. During measurements, care must be taken not to operate in the dropout

region of the regulator under test. VIN2MIN refers to the minimum allowed input voltage for a particular output voltage.

Table 105. VGEN5 electrical characteristics

All parameters are specified at PF0100Z TA = -40 °C to 85 °C, PF0100AZ TA = -40 °C to 105 °C, VIN = 3.6 V, VIN3 = 3.6 V,

VGEN5[3:0] = 1111, IGEN5 = 10 mA, typical external component values, unless otherwise noted. Typical values are characterized at

VIN = 3.6 V, VIN3 = 3.6 V, VGEN5[3:0] = 1111, IGEN5 = 10 mA, and 25 °C, unless otherwise noted.

Symbol

Parameter

Min

Typ

Max

Unit

Notes

VGEN5

VIN3

Operating input voltage

1.8 V

≤ VGEN5NOM ≤ 2.5 V

2.6 V

≤ VGEN5NOM ≤ 3.3 V

2.8

VGEN5NO

M+ 0.250

–

4.5

(69)

VGEN5NOM

Nominal output voltage

–

Table 92

–V

IGEN5

Operating load current

0.0

–

100

VGEN5 active mode – DC

VGEN5TOL

Output voltage tolerance

VIN3MIN < VIN3 < 4.5 V

0.0 mA < IGEN5 < 100 mA

VGEN5[3:0] = 0000 to 1111

-3.0

–

3.0

VGEN5LOR

Load regulation

(VGEN5 at IGEN5 = 100 mA) - (VGEN5 at IGEN5 = 0.0 mA)

For any VIN3MIN < VIN3 < 4.5 mV

–

0.10

–

mV/mA

VGEN5LIR

Line regulation

(VGEN5 at VIN3 = 4.5 V) - (VGEN5 at VIN3MIN)

For any 0.0 mA < IGEN5 < 100 mA

–

0.50

–

mV/mA

IGEN5LIM

Current limit

IGEN5 when VGEN5 is forced to VGEN5NOM/2

122

167

200

IGEN5OCP

Overcurrent protection threshold

IGEN5 required to cause the SCP function to disable LDO when

REGSCPEN = 1

120

–

200

Table 104. VGEN4 electrical characteristics (continued)

All parameters are specified at PF0100Z TA = -40 °C to 85 °C, PF0100AZ TA = -40 °C to 105 °C, VIN = 3.6 V, VIN2 = 3.6 V,

VGEN4[3:0] = 1111, IGEN4 = 10 mA, typical external component values, unless otherwise noted. Typical values are characterized at

VIN = 3.6 V, VIN2 = 3.6 V, VGEN4[3:0] = 1111, IGEN4 = 10 mA, and 25 °C, unless otherwise noted.

Symbol

Parameter

Min

Typ

Max

Unit

Notes

MMPF0100Z 데이터시트(PDF) 87 Page - NXP Semiconductors

MMPF0100Z 데이터시트(HTML) 87 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL