| 전자부품 데이터시트 검색엔진 |
|
82801E 데이터시트(PDF) 35 Page - Intel Corporation |
|
|
|||||||||||||||||||||||||||||
82801E 데이터시트(HTML) 35 Page - Intel Corporation |
|
35 / 84 page ![]() Intel® 82801E C-ICH Advance Information Datasheet 35 TRDY# I/O Target Ready: TRDY# indicates the 82801E C-ICH’s ability as a Target to complete the current data phase of the transaction. TRDY# is used in conjunction with IRDY#. A data phase is completed when both TRDY# and IRDY# are sampled asserted. During a read, TRDY# indicates that the 82801E C-ICH, as a Target, has placed valid data on AD[31:0]. During a write, TRDY# indicates the 82801E C-ICH, as a Target is prepared to latch data. TRDY# is an input to the 82801E C-ICH when the 82801E C-ICH is the Initiator and an output from the 82801E C-ICH when the 82801E C-ICH is a Target. TRDY# is tri-stated from the leading edge of PCIRST#. TRDY# remains tri-stated by the 82801E C-ICH until driven by a target. UART_CLK I Input clock to the SIU. This clock is passed to the baud clock generation logic of each UART in the SIU. USBP0P USBP0N USBP1P USBP1N I/O Universal Serial Bus Port 1:0 Differential: These differential pairs are used to transmit Data/Address/Command signals for ports 0 and 1. V_CPU_IO Powered by the same supply as the processor I/O voltage. This supply is used to drive the processor interface outputs. V5REF Reference for 5 V tolerance on Core well inputs. VBIAS RTC well bias voltage. The DC reference voltage applied to this pin sets a current that is mirrored throughout the oscillator and buffer circuitry. See “External RTC Circuitry” on page 50. Vcc1_8 1.8 V supply for Core well logic. Vcc3_3 3.3 V supply for Core well I/O buffers. VccRTC 3.3 V (can drop to 2.0 V minimum in the G3 state) supply for the RTC well. This power is not expected to be shut off unless the RTC battery is removed or completely drained. NOTE: Implementations should not attempt to clear CMOS by using a jumper to pull VccRTC low. Clearing CMOS in an 82801E C-ICH-based platform can be done by using a jumper on RTCRST# or GPI, or using SAFEMODE strap. VRMPWRGD I VRM Power Good: This can be considered to be the CPU’s VRM power good. This signal should be ANDed with the ATX power supply’s PWROK signal. Vss Grounds. Table 6. 82801E C-ICH Signal Description (Sheet 11 of 11) Signal Type Description |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |