 |
전자부품 데이터시트 검색엔진 |
|
|
전자부품 데이터시트 검색엔진 |
|
GD25B256DFIS 데이터시트(PDF) 55 Page - GigaDevice Semiconductor (Beijing) Inc. |
|
|
|||||||||||||||||||||||||||||
GD25B256DFIS 데이터시트(HTML) 55 Page - GigaDevice Semiconductor (Beijing) Inc. |
|
|
55 / 82 page  3.3V Uniform Sector Dual and Quad Serial Flash GD25B256D 55 Write Extended Addr. Register C5 Yes Yes Extended Addr. Register may need to be changed during a suspend to reach a sector needed for read or program. Read 03 Yes Yes All array reads allowed in suspend. 4Read 13 Yes Yes All array reads allowed in suspend. Fast Read 0B Yes Yes All array reads allowed in suspend. 4Fast Read 0C Yes Yes All array reads allowed in suspend. Dual I/O Fast Read BB Yes Yes All array reads allowed in suspend. 4Dual I/O Fast Read BC Yes Yes All array reads allowed in suspend. Dual Output Fast Read 3B Yes Yes All array reads allowed in suspend. 4Dual Output Fast Read 3C Yes Yes All array reads allowed in suspend. Quad I/O Fast Read EB Yes Yes All array reads allowed in suspend. 4Quad I/O Fast Read EC Yes Yes All array reads allowed in suspend. Quad Output Fast Read 6B Yes Yes All array reads allowed in suspend. 4Quad Output Fast Read 6C Yes Yes All array reads allowed in suspend. Page Program 02 Yes Required for array program during erase suspend. 4Page Program 12 Yes Required for array program during erase suspend. Quad Page Program 32 Yes Required for array program during erase suspend. 4Quad Page Program 34 Yes Required for array program during erase suspend. Program/Erase Resume 7A Yes Required to resume from erase/program suspend. Enable Reset 66 Yes Yes Reset allowed anytime. Reset 99 Yes Yes Reset allowed anytime. The Program/Erase Suspend command will be accepted by the device only if the SUS2/SUS1 bit in the Status Register equal to 0 and WIP bit equal to 1 while a Page Program or a Sector or Block Erase operation is on-going. If the SUS2/SUS1 bit equal to 1 or WIP bit equal to 0, the Suspend command will be ignored by the device. The WIP bit will be cleared fro m 1 to 0 within “tsus” and the SUS2/SUS1 bit will be set from 0 to 1 immediately after Program/Erase Suspend. A power-off during the suspend period will reset the device and release the suspend state. Figure 63 Program/Erase Suspend Sequence Diagram Command 0 1 2 3 4 5 6 7 75H CS# SCLK SI SO High-Z tSUS Accept read command |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Korean ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
