LPC47M14X datasheet(17/205 Pages) SMSC

17 / 205 page

SMSC DS – LPC47M14X

Page 17

Rev. 03/19/2001

POWER FUNCTIONALITY

The LPC47M14x has three power planes: VCC, VTR, and VREF.

5.1

VCC POWER

The LPC47M14x is a 3.3 Volt part. The VCC supply is 3.3 Volts (nominal). See the “Operational Description” Section

and the “Maximum Current Values” subsection.

5.1.1

3 Volt Operation / 5 Volt Tolerance

The LPC47M14x is a 3.3 Volt part. It is intended solely for 3.3V applications. All signal pins are 5V tolerant except

those that pertain to the LPC Bus and USB Hub interfaces; that is, the input voltage is 5.5V max, and the I/O buffer

output pads are backdrive protected.

The LPC interface pins are 3.3 V only. These signals meet PCI DC specifications for 3.3V signaling. These pins are:

LAD[3:0]

LFRAME#

LDRQ#

LPCPD#

The USB interface pins are 3.3V tolerant. The maximum input voltage tolerated on the downstream port pins is 3.6V

(See “Operational Description” for the IOUSB buffers). These pins are labeled:

PD+[1:4]

PD-[1:4]

The input voltage for all other pins is 5.5V max including the following pins:

PCI_RESET#

PCI_CLK

SER_IRQ

nIO_PME

nUSBOC[1:4]

nPWREN[1:4]

5.2

USB POWER

The LPC47M14x requires that the USB Hub maintain power for wake-up events in the absence of VCC power. To

meet these requirements, the Hub Block and the transceiver pins are powered by VTR. CLKI32, which is also

resume from a suspend state by receiving a signal on either its downstream ports or its upstream port.

5.3

VTR SUPPORT

The LPC47M14x requires a trickle supply (VTR) to provide sleep current for the programmable wake-up events in the

PME interface when VCC is removed. The VTR pin is connected to the VTR (standby) power supply, which is 3.3

Volts (nominal). See the “Operational Description” Section. The maximum VTR current that is required depends on

the functions that are used in the part. See “Trickle Power Functionality” subsection and “Maximum Current Values”

subsection. This voltage source is also used to power the USB Hub interface, the IR interface, the PME configuration

registers, and the PME interface. The VTR pin generates a VTR Power-on-Reset signal to initialize these components.

Note:

If VTR is to be used for programmable wake-up events when VCC is removed, VTR must be at its full

minimum potential at least 10

µs before Vcc begins a power-on cycle. When VTR and Vcc are fully

powered, the potential difference between the two supplies must not exceed 500mV.

5.4

VREF PIN

The LPC47M14x has a reference voltage pin input on pin 44 of the part. This reference voltage can be connected to

either a 5V supply or a 3.3V supply. It is used for the game port. See the “GAME PORT LOGIC” section.

LPC47M14X 데이터시트(PDF) 17 Page - SMSC Corporation

LPC47M14X 데이터시트(HTML) 17 Page - SMSC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL