L9966 datasheet(10/122 Pages) STMICROELECTRONICS

10 / 122 page

5.3

ESD trials

ESD requirements for the stand-alone component (without any external circuits).

Table 4. ESD

Parameter

Value

Unit

ESD according to the Human Body Model (HBM), Q100-002 for global pins; (100 pF/1.5 kΩ)

±4000

ESD according to the Human Body Model (HBM), Q100-002 for all pins; (100 pF/1.5 kΩ)

±2000

ESD according to the Charged Device Model (CDM), Q100-011 Corner pins

±750

ESD according to the Charged Device Model (CDM), Q100-011 All pins

±500

5.4

Operating voltage ranges

Table 5. Supply operating ranges summarizes the different operating ranges where different functionalities of the

FlexInput are guaranteed. It is assumed that the junction temperature range for proper functionality goes from

-40 °C up to 150 °C, unless otherwise specified.

Table 5. Supply operating ranges

Operation

Range

UBSW (V)

VDD5 (V)

Remark

Load Dump

36 – 58

Parameters can be out of tolerance (if RST=’1’), system is not damaged for

pulse duration of 500 ms, 10 time in life.

Jump start

0 – 48

Parameter can be out of tolerance (if RST=’1’), system is not damaged for

pulse duration of 60 s, 10 time in life.

Normal

7.5 – 36

4.85 –

5.15

All parameters in spec. with VDD5_REF = 5 V(1)

Low Batt

5.5 – 7.5

4.85 –

5.15

All parameters in spec. with VDD5_REF = 5 V(1) Current sources can be out

of tolerance, but still non-zero.

Resistance measurement is guaranteed for UBSW-V(IO)>1.5 V that means if

UBSW = 5.5 V → IOx<4 V

Normal, Low

VDD5

7.5 – 36

4 – 4.85

All parameters in spec. Digital and AOX output buffers still working, voltages

limited by VDD5 voltage. 5 V_REF, VVAR and VADCxREF are scaled down

to VDD5 voltage.

Low Batt, Low

VDD5

5.5 – 7.5

4 – 4.85

All parameters in spec. Current sources can be out of tolerance, but still

non-zero. Digital and AOX output buffers still working, voltages limited by

VDD5 voltage. 5V_REF, VVAR and VADCxREF are scaled down.

Resistance measurement is guaranteed for UBSW-V(IO)>1.5V that means if

UBSW = 5.5 V → IOx<4 V

Low Batt – 3V3

digital fault

3V3_FLT – 5.5

Configuration data is kept;

Input buffer is not able to reach 5 V full range;

VRS and SPI functionalities are in spec for UBSW down to 4.5 V.

SPI (frequency is not guaranteed) still run down to POR.

All analog functions are still on but parameters are out of tolerance.

VRS hysteresis features are not guaranteed in case UBSW is < 4.5 V.

3V3 digital fault

VPOR –

3V3_FLT

If 3V3_FLT = 1 all functions switched off. Only internal charge pump kept on

to guarantee no reset of internal logic

Low Batt

< VPOR

Device in OFF mode

1. The parameters depending on VDD5_REF are: ADC1 accuracy, pull-up voltage 5V and VVAR. They will have the same

tolerance in addition as VDD5_REF.

L9966

ESD trials

DS12459 - Rev 10

page 10/122

L9966 데이터시트(PDF) 10 Page - STMicroelectronics

L9966 데이터시트(HTML) 10 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL