CS47L85 datasheet(52/370 Pages) CIRRUS

52 / 370 page

CS47L85

Rev 4.3

INPUT SIGNAL PATH ENABLE

The input signal paths are enabled using the register bits described in Table 2. The respective bit(s) must be enabled for

analogue or digital input on the respective input path(s).

The input signal paths are muted by default. It is recommended that de-selecting the mute should be the final step of the

path enable control sequence. Similarly, the mute should be selected as the first step of the path disable control sequence.

The input signal path mute functions are controlled using the register bits described in Table 4.

The MICVDD power domain must be enabled when using the analogue input signal path(s). This power domain is provided

using an internal Charge Pump (CP2) and LDO Regulator (LDO2). See “Charge Pumps, Regulators and Voltage Reference”

for details of these circuits.

The system clock, SYSCLK, must be configured and enabled before any audio path is enabled. The input signal paths

should be kept disabled (INnx_ENA=0) if SYSCLK is not enabled. The ASYNCCLK and 32kHz clock may also be required,

depending o

n the path configuration. See “Clocking and Sample Rates” for details of the system clocks (including

requirements for reconfiguring SYSCLK while audio paths are enabled).

The CS47L85 performs automatic checks to confirm that the SYSCLK frequency is high enough to support the input signal

paths and associated ADCs. If an attempt is made to enable an input signal path, and there are insufficient SYSCLK cycles

to support it, then the attempt will be unsuccessful. (Note that any signal paths that are already active will not be affected

under these circumstances.)

The status bits in Register R769 indicate the status of each of the input signal paths. If an Underclocked Error condition

occurs, then these bits provide readback of which input signal path(s) have been successfully enabled.

ADDRESS

BIT

LABEL

DEFAULT

DESCRIPTION

R768

(0300h)

Input_Ena

bles

IN6L_ENA

Input Path 6 (Left) Enable

0 = Disabled

1 = Enabled

IN6R_ENA

Input Path 6 (Right) Enable

0 = Disabled

1 = Enabled

IN5L_ENA

Input Path 5 (Left) Enable

0 = Disabled

1 = Enabled

IN5R_ENA

Input Path 5 (Right) Enable

0 = Disabled

1 = Enabled

IN4L_ENA

Input Path 4 (Left) Enable

0 = Disabled

1 = Enabled

IN4R_ENA

Input Path 4 (Right) Enable

0 = Disabled

1 = Enabled

IN3L_ENA

Input Path 3 (Left) Enable

0 = Disabled

1 = Enabled

IN3R_ENA

Input Path 3 (Right) Enable

0 = Disabled

1 = Enabled

IN2L_ENA

Input Path 2 (Left) Enable

0 = Disabled

1 = Enabled

IN2R_ENA

Input Path 2 (Right) Enable

0 = Disabled

1 = Enabled

IN1L_ENA

Input Path 1 (Left) Enable

0 = Disabled

1 = Enabled

IN1R_ENA

Input Path 1 (Right) Enable

0 = Disabled

1 = Enabled

CS47L85 데이터시트(PDF) 52 Page - Cirrus Logic

CS47L85 데이터시트(HTML) 52 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL