| 전자부품 데이터시트 검색엔진 |
|
XRT86VL34 데이터시트(PDF) 53 Page - Exar Corporation |
|
|
|||||||||||||||||||||||||||||
XRT86VL34 데이터시트(HTML) 53 Page - Exar Corporation |
|
53 / 156 page ![]() XRT86VL34 48 REV. V1.2.0 QUAD T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 32: RECEIVE INTERFACE CONTROL REGISTER (RICR) HEX ADDRESS: 0XN122 BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 7 RxSyncFrD R/W 0 Receive Synchronous fraction data interface This bit selects whether RxCHCLK or RxSERCLK will be used for fractional data output if receive fractional interface is enabled. If RxSERCLK is selected to clock out fractional data, RxCHCLK will be used as an enable signal 0 = Fractional data Is clocked out of the chip using RxChCLK if the receive fractional interface is enabled. 1 = Fractional data is clocked out of the chip using RxSerClk if the receive fractional interface is enabled. RxChClk is used as fractional data enable. NOTE: The Time Slot Identifier Pins (RxChn[4:0]) still indicates the time slot number if the receive fractional data interface is not enabled. Fractional Interface can be enabled by setting RxFr1544 to 1 6 Reserved - - Reserved 5 RxPLClkEnb/ RxSync is low R/W 0 Receive payload clock enable/RxSYNC is Active Low This exact function of this bit depends on whether the T1 framer is configured to operate in base rate or high speed modes of operation. If the T1 framer is configured to operate in base rate - TxPayload Clock: This bit configures the T1 framer to either output a regular clock or a payload clock on the receive serial clock (RxSERCLK) pin when RxSERCLK is config- ured to be an output. 0 = Configures the framer to output a 1.544MHz clock on the RxSERCLK pin when RxSERCLK is configured as an output. 1 = Configures the framer to output a 1.544MHz clock on the RxSERCLK pin when receiving payload bits. There will be gaps on the RxSERCLK output pin when receiving overhead bits. If the T1 framer is configured to operate in high-speed or multiplexed modes - RxSYNC is Active Low: This bit is used to select whether the receive frame boundary (RxSYNC) is active low or active high. 0 = Selects RxSync to be active “High” 1 = Selects RxSync to be active “Low” |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |