| 전자부품 데이터시트 검색엔진 |
|
L9679E 데이터시트(PDF) 82 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
L9679E 데이터시트(HTML) 82 Page - STMicroelectronics |
|
82 / 127 page ![]() 8.1 PSI-5 mode All channels are compliant to the PSI-5 v1.3 specification as described below: • Two-wire current interface • Manchester coded digital data transmission • High data transmission speeds of 125 kbps and 189 kbps • Variable data word length (8- and 10-bit only) • 1-bit parity • Asynchronous operating mode with 3 stage input data buffers • Synchronous operating mode with 3 time slots An example of the data format for one possible PSI-5 protocol configuration is shown below. Data size and the error checking may vary, but the presence of 2 sync start bits (referenced below as sync bits) and 2 TGap time is consistent regardless. Figure 21. PSI-5 remote sensor protocol (10-bit, 1-bit parity) Data Transmission Manchester Code Transmission of 0x1E7 0x1E7 = 01 1110 0111b frame duration T BIT T Gap S1 "0" S2 "0" D0 "1" D1 "1" D2 "1" D3 "0" D4 "0" D5 "1" D6 "1" D7 "1" D8 "1" D9 "0" P "1" GADG0903181523PS 8.1.1 Functional description The remote sensor interface block provides a hardware connection between the microcontroller and up to twelve remote sensors (maximum three per channel). Each channel is independent from the others, and is not influenced by possible fault conditions occurring on other channels, such as shortcircuits to ground or to vehicle battery. Each channel is supplied by a current limited DC voltage derived from VSAT pin, and monitors the current sunk from its supply in order to extract encoded data. The remote sensor modulates the current draw to transmit Manchester-encoded data back to the receiver. The current level detection threshold for all channels is internally computed by the IC in order to adapt the signal level to the sensors quiescent current. All channels can be enabled or disabled independently via SPI commands. The operational status of all channels can also be read via SPI command. All channels support individual selective sync-pulse control to allow communication back to the remote sensor via sync-pulse voltage modulation as described in the PSI5 v1.3 specification. In case asynchronous mode is selected for one interface the sync pulse is not generated (sync pulse control bit is don’t care). The message bits are encoded using a Manchester format, in which logic values are determined by a current transition in the middle of the bit time. When configured for PIS5 sensors each interface supports Manchester 2 encoding as shown in Figure 22. Manchester bit encoding. Figure 22. Manchester bit encoding Logic '0' Logic '1' Manchester-2 PSI5 Bit time ‘0’ ‘0’ ‘1’ ‘0’ ‘1’ Current Start bits = ‘00’ GADG0903181529PS L9679E Remote sensor interface DS12485 - Rev 8 page 82/127 |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |