| 전자부품 데이터시트 검색엔진 |
|
MAXQ3180-RAN+ 데이터시트(PDF) 36 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
MAXQ3180-RAN+ 데이터시트(HTML) 36 Page - Maxim Integrated Products |
|
36 / 48 page ![]() Highpass Filter (HPF) A simple first-order highpass filter (HPF) is used.The fil- ter formula is: Yn = (1 - hpf_b0f/216) x (Yn-1 + Xn - Xn-1) The filter coefficient (hpf_b0f) is a signed 16-bit value and can be configured by the master. Integrator The digital integrator block can be engaged separately for each current phase (IA, IB, IC) and for neutral cur- rent (IN) by setting configuration bits INTGA, INTGB, INTGC, and INTGN in the CONNCT register. When enabled, the digital integrator block calculates the inte- gral of the input current signal (i.e., sum of samples) and then feeds this integral into the processing path instead of the current sample. This sum can produce a DC offset that must be removed by an additional HPF stage. The HPF can be combined with the integrator in a single formula: Yn = (1 - hpf_b0f/216) x (Yn-1 + Xn) where hpf_b0f is the same coefficient used in the stand-alone HPF stage. The integrator increases the amplitude of accumulation by approximately (NS/2 π), where NS is the number of samples per line cycle (fac- tor approximately 16 for 50Hz signal and 200μs sam- pling rate). The output of the integrator is scaled down by factor 16 in the MAXQ3180. The HPF, when combined with the digital integrator, introduces an additional phase shift into the current channel. To compensate for this, the second HPF stage is automatically engaged in the voltage processing path when the current integrator is active. Fundamental and Harmonics Modes The power calculation engine can work in one of three modes: full, fundamental, and harmonics. The mode of operation is selected by the HRM configuration bits. • HRM = 00b—Full mode. Neither the bandpass or the bandstop filters are applied. • HRM = 01b—Fundamental mode. The voltage chan- nel signal is put through the bandpass filter (BPF). This BPF is centered on the fundamental frequency, so only fundamental power is measured. • HRM = 10b—Harmonics mode. The voltage channel signal is put through the bandstop filter (BSF). That BSF is centered on the fundamental frequency, so fundamental power is removed and only harmonics power is measured. Both filters, the BPF and BSF, are second-order filters and use the same set of coefficients. The filter formulas are: BPF: Yn = 2Yn-1 - Yn-2 + (bpf_b0f/220) x (2Yn-2 + Xn - Xn-2) - (bpf_a1f/220) x Yn-1 BSF: Yn = 2Yn-1 - Yn-2 + Xn - 2Xn-1 - Xn-2 + (bpf_b0f/220) x (2Yn-2 - Xn - Xn-2) + (bpf_a1f/220) x (Xn-1 - Yn-1) Low-Power, Multifunction, Polyphase AFE 36 ______________________________________________________________________________________ INTEGRATOR + HPF PHASE ANGLE COMPENSATION GAIN, OFFSET, AND LINEARITY CALIBRATION SI2 I2_RMS V2_RMS P.V2 ACTIVE REACTIVE HPF HPF I SV2 S HPF V BPF BSF P.R P.A P.I2 Figure 8. DSP Flow |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |