STLC1502 datasheet(47/81 Pages) STMICROELECTRONICS

47 / 81 page

47/81

STLC1502

•

The SDA/SCL lines are released after the transfer of the current byte.

7.6.3.2 Master Mode

To switch from default Slave mode to Master mode a Start condition generation is needed.

Start condition

Setting the START bit while the BUSY bit is cleared causes the interface to switch to Master mode (M/SL

bit set) and generates a Start condition. Once the Start condition is sent:

– The EVF and SB bits are set by hardware with an interrupt if the ITE bit is set.

Then the master waits for a read of the SR1 register followed by a write in the DR register with the Slave

address, holding the SCL line low.

Slave address transmission

The slave address is then sent to the SDA line via the internal shift register.

In 7-bit addressing mode, one address byte is sent.

In 10-bit addressing mode, sending the first byte including the header sequence causes the following

event:

– The EVF bit is set by hardware with interrupt generation if the ITE bit is set.

Then the master waits for a read of the SR1 register followed by a write in the DR register, holding the

SCL line low. The second address byte is then sent by the interface. After completion of this transfer (and

acknowledge from the slave if the ACK bit is set):

– The EVF bit is set by hardware with interrupt generation if the ITE bit is set.

Then the master waits for a read of the SR1 register followed by a write in the CR register (for example

set PE bit), holding the SCL line low. Next the master must enter Receiver or Transmitter mode.

Note: In 10-bit addressing mode, to switch the master to Receiver mode, software must generate a

repeated Start condition and resend the header sequence with the least significant bit set (11110xx1).

Master Receiver

After the address transmission and SR1 and CR registers have been accessed, the master receives

bytes from the SDA line into the DR register via the internal shift register. After each byte the interface

generates in sequence:

– Acknowledge pulse if the ACK bit is set

– EVFand BTF bits are set by hardware with an interrupt if the ITE bit is set.

Then the interface waits for a read of the SR1 register followed by a read of the DR register, holding the

SCL line low. To close the communication: before reading the last byte from the DR register, set the

STOP bit to generate the Stop condition. The interface goes automatically back to slave mode (M/SL bit

cleared).

Note: In order to generate the non-acknowledge pulse after the last received data byte, the ACK bit must

be cleared just before reading the second last data byte.

Master Transmitter

After the address transmission and SR1 register has been read, the master sends bytes from the DR

lowed by a write in the DR register, holding the SCL line low. When the acknowledge bit is received, the

interface sets:

– EVF and BTF bits with an interrupt if the ITE bit is set.

To close the communication: after writing the last byte to the DR register, set the STOP bit to generate

the Stop condition. The interface goes automatically back to slave mode (M/SL bit cleared).

STLC1502 데이터시트(PDF) 47 Page - STMicroelectronics

STLC1502 데이터시트(HTML) 47 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81

데이터시트 다운로드

링크 URL