ATmega64A datasheet(141/392 Pages) ATMEL

141 / 392 page

141

8160C–AVR–07/09

ATmega64A

15.11.19 TIFR – Timer/Counter Interrupt Flag Register

(1)

Note:

1. This register contains flag bits for several Timer/Counters, but only Timer1 bits are described

in this section. The remaining bits are described in their respective timer sections.

• Bit 5 – ICF1: Timer/Counter1, Input Capture Flag

This flag is set when a capture event occurs on the ICP1 pin. When the Input Capture Register

(ICR1) is set by the WGMn3:0 to be used as the TOP value, the ICF1 flag is set when the coun-

ter reaches the TOP value.

ICF1 is automatically cleared when the Input Capture Interrupt Vector is executed. Alternatively,

ICF1 can be cleared by writing a logic one to its bit location.

• Bit 4 – OCF1A: Timer/Counter1, Output Compare A Match Flag

This flag is set in the timer clock cycle after the counter (TCNT1) value matches the Output

Compare Register A (OCR1A).

Note that a Forced Output Compare (FOC1A) strobe will not set the OCF1A flag.

OCF1A is automatically cleared when the Output Compare Match A Interrupt Vector is exe-

cuted. Alternatively, OCF1A can be cleared by writing a logic one to its bit location.

• Bit 3 – OCF1B: Timer/Counter1, Output Compare B Match Flag

This flag is set in the timer clock cycle after the counter (TCNT1) value matches the Output

Compare Register B (OCR1B).

Note that a Forced Output Compare (FOC1B) strobe will not set the OCF1B flag.

OCF1B is automatically cleared when the Output Compare Match B Interrupt Vector is exe-

cuted. Alternatively, OCF1B can be cleared by writing a logic one to its bit location.

• Bit 2 – TOV1: Timer/Counter1, Overflow Flag

The setting of this flag is dependent of the WGMn3:0 bits setting. In Normal and CTC modes,

the TOV1 flag is set when the timer overflows. Refer to Table 15-5 on page 135 for the TOV1

flag behavior when using another WGMn3:0 bit setting.

TOV1 is automatically cleared when the Timer/Counter1 Overflow Interrupt Vector is executed.

Alternatively, TOV1 can be cleared by writing a logic one to its bit location.

15.11.20 ETIFR – Extended Timer/Counter Interrupt Flag Register

• Bit 7:6 – Reserved Bits

These bits are reserved for future use. For ensuring compatibility with future devices, these bits

must be set to zero when ETIFR is written.

Bit

765

43210

0x36 (0x56)

OCF2

TOV2

ICF1

OCF1A

OCF1B

TOV1

OCF0

TOV0

TIFR

Read/Write

R/W

Initial Value

000

00000

Bit

765

4321

(0x7C)

–

ICF3

OCF3A

OCF3B

TOV3

OCF3C

OCF1C

ETIFR

Read/Write

R/W

Initial Value

000

0000

ATmega64A 데이터시트(PDF) 141 Page - ATMEL Corporation

ATmega64A 데이터시트(HTML) 141 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL