SPC564L54L5 datasheet(158/160 Pages) STMICROELECTRONICS

158 / 160 page

Revision history

SPC56XL60/54

158/160

Doc ID 15457 Rev 8

01-Aug-2012

(cont.)

Changed min value to ‘-72’ for symbol ‘THD’.

–In Table 26 (ADC conversion characteristics), changed ADC specification

parameter ‘THD’ minimum limit from -72 to -65dB.

–In Table 27 (Flash memory program and erase electrical specifications),

changes done are as follows:

TDWPROGRAM, changed typical value from ‘39’ to ‘38’.

TPPROGRAM, changed typical value from ‘48’ to ‘45’ and intial max value from

‘100’ to ‘160’.

T16KPPERASE, inserted typical value ‘270’ and factory avg ‘1000’.

T48KPPERASE, inserted typical value ‘625’ and factory avg ‘1500’.

T64KPPERASE, inserted typical value ‘800’ and factory avg ‘1800’.

T128KPPERASE, inserted typical value ‘1500’ and factory avg ‘2600’.

T256KPPERASE, inserted typical value ‘3000’ and factory avg ‘5200’.

Updated table footnote and removed min column in Table 27 (Flash memory

program and erase electrical specifications)

–In Table 28 (Flash memory timing), added symbol TPSRT ,TESRT and added

table footnote for TPSRT ,TESRT .

– Added Table 30 (MPC5643L SWG Specifications)

–In Table 30 (MPC5643L SWG Specifications)

Added table footnote for Common Mode.

Changed text from “internal device pad resistance” to “internal device routing

resistance”.

– Added Figure 27 in Section 3.20.4, “Nexus timing”.

–In Table 31 (Pad AC specifications (3.3 V , IPP_HVE = 0 )), removed the row

of pad “Pull Up/Downc(3.6 V max)”.

–In Figure 43, updated part numbers (changed ‘PPC’ to ‘SPC’ and ‘F0’ to

‘F2’).

–Replaced Figure 41, Figure 42 with the new versions.

–InTable 19 (Voltage regulator electrical specifications),changed the symbol

of spec external decoupling capacitor from SR to Cext.

In Figure 5, changed the ESR range in note text to 1 mW to 100 mW from

30 mW to 150 mW.

–In Section 1.5.32, “Sine Wave Generator (SWG)” removed the following text:

Frequency range from 1kHz to 50kHz.

Sine wave amplitude from 0.47 V to 2.26 V.

–In Table 21 (Current consumption characteristics),changed symbol from ‘C’

to ‘T’ , added “operating current” to the parameter and updated the maximum

value for five additional RunIDD parameters.

–In Table 21 (Current consumption characteristics), changed “Conditions”

from ‘1.2 V supplies’ to ‘1.2 V supplies during LBIST (full LBIST

configuration)’ for all the parameters.

Removed Table “SWG electrical characteristics”.

Table 44.

Document revision history (continued)

Date

Revision

Changes

SPC564L54L5 데이터시트(PDF) 158 Page - STMicroelectronics

SPC564L54L5 데이터시트(HTML) 158 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL