WM8352 datasheet(56/336 Pages) WOLFSON

56 / 336 page

WM8352

Production Data

PD, February 2011, Rev 4.4

The field FLL_RATE controls internal functions within the FLL; it is recommended that only the

default setting be used for this parameter. FLL_RSP_RATE controls the internal loop gain and

should be set to the recommended value.

The FLL output frequency is directly determined from FLL_RATIO, FLL_OUTDIV and the real

number represented by FLL_N and FLL_K. The field FLL_N is an integer (LSB = 1); FLL_K is the

fractional portion of the number (MSB = 0.5). The fractional portion is only valid when enabled by the

field FLL_FRAC. It is recommended that FLL_FRAC is enabled at all times.

The FLL frequency is determined according to the following equation:

FOUT = (FVCO / FLL_OUTDIV)

FVCO = (FREF x N.K x FLL_RATIO)

FVCO must be in the range 90-100 MHz. The value of FLL_OUTDIV should be selected as follows

according to the desired output FOUT.

OUTPUT FREQUENCY FOUT

FLL_OUTDIV

2.8125 MHz - 3.125 MHz

4h (divide by 32)

5.625 MHz - 6.25 MHz

3h (divide by 16)

11.25 MHz - 12.5 MHz

2h (divide by 8)

22.5 MHz - 25 MHz

1h (divide by 4)

Table 16 Choice of FLL_OUTDIV

Note that the output frequencies that do not lie within the ranges quoted above cannot be guaranteed

across the full range of device operating temperatures.

Once FVCO has been determined, the value of FLL_RATIO should be selected in accordance with the

recommendations in Table 17. The value of N.K can then be determined using the equation above.

FLL_REF_FREQ should be set as described in Table 17.

For best performance, FLL Fractional Mode should always be used. Therefore, if the calculations

yield an integer value of N.K, then it is recommended to adjust FLL_RATIO in order to obtain a non-

integer value of N.K.

The register fields that control the FLL are described in Table 17. Example settings for a variety of

reference frequencies and output frequencies are shown in Table 18.

ADDRESS

BIT

LABEL

DEFAULT

DESCRIPTION

R42 (2Ah)

FLL Control 1

FLL_ENA

Digital Enable for FLL

0 = disabled

1 = enabled

Note that FLL_OSC_ENA must be

enabled before enabling FLL_ENA.

FLL_OSC_EN

Analogue Enable for FLL

0 = FLL disabled

1 = FLL enabled

Note that FLL_OSC_ENA must be

enabled before enabling FLL_ENA.

10:8

FLL_OUTDIV

[2:0]

010

FOUT clock divider

000 = FVCO / 2

001 = FVCO / 4

010 = FVCO / 8

011 = FVCO / 16

100 = FVCO / 32

101 = Reserved

110 = Reserved

WM8352 데이터시트(PDF) 56 Page - Wolfson Microelectronics plc

WM8352 데이터시트(HTML) 56 Page - Wolfson Microelectronics plc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL