PIC16F883-ESLASHSO. datasheet(157/338 Pages) MICROCHIP

157 / 338 page

 2006-2012 Microchip Technology Inc.

DS41291G-page 157

PIC16F882/883/884/886/887

12.1

EUSART Asynchronous Mode

The EUSART transmits and receives data using the

standard non-return-to-zero (NRZ) format. NRZ is

implemented with two levels: a VOH mark state which

represents a ‘1’ data bit, and a VOL space state which

represents a ‘0’ data bit. NRZ refers to the fact that

consecutively transmitted data bits of the same value

stay at the output level of that bit without returning to a

neutral level between each bit transmission. An NRZ

transmission port idles in the mark state. Each character

transmission consists of one Start bit followed by eight

or nine data bits and is always terminated by one or

more Stop bits. The Start bit is always a space and the

Stop bits are always marks. The most common data

format is 8 bits. Each transmitted bit persists for a period

of 1/(Baud Rate). An on-chip dedicated 8-bit/16-bit Baud

Rate Generator is used to derive standard baud rate

frequencies from the system oscillator. See Table 12-5

for examples of baud rate configurations.

The EUSART transmits and receives the LSb first. The

EUSART’s transmitter and receiver are functionally

independent, but share the same data format and baud

rate. Parity is not supported by the hardware, but can

be implemented in software and stored as the ninth

data bit.

12.1.1

EUSART ASYNCHRONOUS

TRANSMITTER

The EUSART transmitter block diagram is shown in

Figure 12-1. The heart of the transmitter is the serial

Transmit Shift Register (TSR), which is not directly

accessible by software. The TSR obtains its data from

the transmit buffer, which is the TXREG register.

12.1.1.1

Enabling the Transmitter

The EUSART transmitter is enabled for asynchronous

operations by configuring the following three control

bits:

•TXEN = 1

• SYNC = 0

• SPEN = 1

All other EUSART control bits are assumed to be in

their default state.

Setting the TXEN bit of the TXSTA register enables the

transmitter circuitry of the EUSART. Clearing the SYNC

bit of the TXSTA register configures the EUSART for

asynchronous operation. Setting the SPEN bit of the

RCSTA

enables

the

EUSART

and

automatically configures the TX/CK I/O pin as an output.

If the TX/CK pin is shared with an analog peripheral the

analog I/O function must be disabled by clearing the

corresponding ANSEL bit.

12.1.1.2

Transmitting Data

A transmission is initiated by writing a character to the

TXREG register. If this is the first character, or the

previous character has been completely flushed from

the TSR, the data in the TXREG is immediately

transferred to the TSR register. If the TSR still contains

all or part of a previous character, the new character

data is held in the TXREG until the Stop bit of the

previous character has been transmitted. The pending

character in the TXREG is then transferred to the TSR

in one TCY immediately following the Stop bit

transmission. The transmission of the Start bit, data bits

and Stop bit sequence commences immediately

following the transfer of the data to the TSR from the

TXREG.

12.1.1.3

Transmit Interrupt Flag

The TXIF interrupt flag bit of the PIR1 register is set

whenever the EUSART transmitter is enabled and no

character is being held for transmission in the TXREG.

In other words, the TXIF bit is only clear when the TSR

is busy with a character and a new character has been

queued for transmission in the TXREG. The TXIF flag

bit is not cleared immediately upon writing TXREG.

TXIF becomes valid in the second instruction cycle

following the write execution. Polling TXIF immediately

following the TXREG write will return invalid results. The

TXIF bit is read-only, it cannot be set or cleared by

software.

The TXIF interrupt can be enabled by setting the TXIE

interrupt enable bit of the PIE1 register. However, the

TXIF flag bit will be set whenever the TXREG is empty,

regardless of the state of TXIE enable bit.

To use interrupts when transmitting data, set the TXIE

bit only when there is more data to send. Clear the

TXIE interrupt enable bit upon writing the last character

of the transmission to the TXREG.

Note 1: When the SPEN bit is set the RX/DT I/O

pin is automatically configured as an input,

regardless of the state of the correspond-

ing TRIS bit and whether or not the

EUSART receiver is enabled. The RX/DT

pin data can be read via a normal PORT

read but PORT latch data output is pre-

cluded.

2: The TXIF transmitter interrupt flag is set

when the TXEN enable bit is set.

PIC16F883-E/SO. 데이터시트(PDF) 157 Page - Microchip Technology

PIC16F883-E/SO. 데이터시트(HTML) 157 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL