PIC16F883-ESLASHSO. datasheet(158/338 Pages) MICROCHIP

158 / 338 page

PIC16F882/883/884/886/887

DS41291G-page 158

 2006-2012 Microchip Technology Inc.

12.1.1.4

TSR Status

The TRMT bit of the TXSTA register indicates the

status of the TSR register. This is a read-only bit. The

TRMT bit is set when the TSR register is empty and is

cleared when a character is transferred to the TSR

until all bits have been shifted out of the TSR register.

No interrupt logic is tied to this bit, so the user has to

poll this bit to determine the TSR status.

12.1.1.5

Transmitting 9-Bit Characters

The EUSART supports 9-bit character transmissions.

When the TX9 bit of the TXSTA register is set the

EUSART will shift 9 bits out for each character transmit-

ted. The TX9D bit of the TXSTA register is the ninth,

and Most Significant, data bit. When transmitting 9-bit

data, the TX9D data bit must be written before writing

the 8 Least Significant bits into the TXREG. All nine bits

of data will be transferred to the TSR shift register

immediately after the TXREG is written.

A special 9-bit Address mode is available for use with

multiple receivers. See Section 12.1.2.7 “Address

Detection” for more information on the Address mode.

12.1.1.6

Asynchronous Transmission Setup:

Initialize the SPBRGH, SPBRG register pair and

the BRGH and BRG16 bits to achieve the desired

baud rate (see Section 12.3 “EUSART Baud

Rate Generator (BRG)”).

Enable the asynchronous serial port by clearing

the SYNC bit and setting the SPEN bit.

If 9-bit transmission is desired, set the TX9 con-

trol bit. A set ninth data bit will indicate that the 8

Least Significant data bits are an address when

the receiver is set for address detection.

Enable the transmission by setting the TXEN

control bit. This will cause the TXIF interrupt bit

to be set.

If interrupts are desired, set the TXIE interrupt

enable bit of the PIE1 register. An interrupt will

occur immediately provided that the GIE and

PEIE bits of the INTCON register are also set.

If 9-bit transmission is selected, the ninth bit

should be loaded into the TX9D data bit.

Load 8-bit data into the TXREG register. This

will start the transmission.

FIGURE 12-3:

ASYNCHRONOUS TRANSMISSION

Note:

The TSR register is not mapped in data

memory, so it is not available to the user.

Word 1

Stop bit

Word 1

Transmit Shift Reg

Start bit

bit 0

bit 1

bit 7/8

Write to TXREG

Word 1

BRG Output

(Shift Clock)

TX/CK

TXIF bit

(Transmit Buffer

Reg. Empty Flag)

TRMT bit

(Transmit Shift

Reg. Empty Flag)

1 TCY

PIC16F883-E/SO. 데이터시트(PDF) 158 Page - Microchip Technology

PIC16F883-E/SO. 데이터시트(HTML) 158 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL