전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

AS8506 데이터시트(PDF) 24 Page - ams AG

부품명 AS8506
상세설명  Battery Cell Monitor and Balancer IC
PDF  89 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  AMSCO [ams AG]
홈페이지  http://www.ams.com
Logo AMSCO - ams AG

AS8506 데이터시트(HTML) 24 Page - ams AG

Back Button AS8506 Datasheet HTML 20Page - ams AG AS8506 Datasheet HTML 21Page - ams AG AS8506 Datasheet HTML 22Page - ams AG AS8506 Datasheet HTML 23Page - ams AG AS8506 Datasheet HTML 24Page - ams AG AS8506 Datasheet HTML 25Page - ams AG AS8506 Datasheet HTML 26Page - ams AG AS8506 Datasheet HTML 27Page - ams AG AS8506 Datasheet HTML 28Page - ams AG Next Button
Zoom Inzoom in Zoom Outzoom out
 24 / 89 page
background image
AS8506 – 24
ams Datasheet, Confidential:2013-Sep [1-00]
De tail ed De sc rip t ion
SAR ADC
AS8506 has a 12-bit SAR ADC to measure the cell voltage and
external temperature. The SAR ADC uses the 12-bit DAC to
generate the digital code. The SAR ADC range is 1.8V to 4.5V for
cell voltage measurement and 0.2V to 4.5V for the temperature
measurement.
Cell voltage and temperature is measured in the short trigger
phase. After the trigger goes ‘high’, compare phase starts and
then all the cell voltages and external temperature are
measured and stored in the digital registers.
Pre-Regulator
AS8506 has an internal pre-regulator, which generates supply
voltages for the internal blocks. Pre-Regulator output is used as
a supply for the oscillators. All the digital logic and the FSM will
work on the pre-regulator supply.
In SLEEP mode only the pre-regulator will be working along with
the WAKE_IN detect circuit.
Cell Threshold
AS8506 has the potential to set the two threshold levels to the
cell voltage through pins CELL_THU and CELL_THL. These
values can be set externally, (or) through OTP trim bits, (or) from
the external microcontroller by writing DAC code into the cell
threshold registers in the register space.
Weak Cell Detection
AS8506 has the ability to detect the weak cell. During load
conditions, if the cell reaches voltage of about 0.1V to -0.2V,
then this variation is detected and stored in the zero cross
detection register. This event is indicated to the master device
by a pulse on CVT_NOK_OUT pin in Compare and Balance
phase. The master device indicates the microcontroller by
setting CVT_NOK_OUT ‘high’. In WAIT mode only this will be
stored in the register; there won’t be any CVT_NOK_OUT to μC.
The register is cleared on μC reading.
External Resister Divider Control
AS8506 has the provision to enable the external divider to give
the desired cell voltage to the at VREF_IN pin. External resister
divider can be connected between VREF_H pin to ground.
Calculate the external resister divider values such that the
output of the divider will provide the desired reference value.
When comparison is not happening, this divider can be
disabled using SPI.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com