AT90LS4433-4AI datasheet(28/126 Pages) ATMEL

28 / 126 page

AT90S/LS4433

1042H–AVR–04/03

• Bit 6 – INTF0: External Interrupt Flag0

When an edge on the INT0 pin triggers an interrupt request, the corresponding Interrupt

Flag, INTF0 becomes set (one). If the I-bit in SREG and the corresponding interrupt

enable bit, INT0 in GIMSK is set (one), the MCU will jump to the Interrupt Vector. The

flag is always cleared when the interrupt routine is executed. Alternatively, the flag is

cleared by writing a logical “1” to it. This flag is always cleared when INT0 is configured

as level interrupt.

• Bits 5..0 – Res: Reserved Bits

These bits are reserved bits in the AT90S4433 and always read as zero.

Timer/Counter Interrupt Mask

• Bit 7 – TOIE1: Timer/Counter1 Overflow Interrupt Enable

When the TOIE1 bit is set (one) and the I-bit in the Status Register is set (one), the

Timer/Counter1 Overflow Interrupt is enabled. The corresponding interrupt (at vector

$005) is executed if an overflow in Timer/Counter1 occurs, i.e., when the TOV1 bit is set

in the Timer/Counter Interrupt Flag Register (TIFR).

• Bit 6 – OCIE1: Timer/Counter1 Output Compare Match Interrupt Enable

When the OCIE1 bit is set (one) and the I-bit in the Status Register is set (one), the

Timer/Counter1 Compare Match Interrupt is enabled. The corresponding interrupt (at

vector $004) is executed if a compare match in Timer/Counter1 occurs, i.e., when the

OCF1 bit is set in the Timer/Counter Interrupt Flag Register (TIFR).

• Bits 5, 4 – Res: Reserved Bits

These bits are reserved bits in the AT90S4433 and always read as zero.

• Bit 3 – TICIE1: Timer/Counter1 Input Capture Interrupt Enable

When the TICIE1 bit is set (one) and the I-bit in the Status Register is set (one), the

Timer/Counter1 Input Capture Event Interrupt is enabled. The corresponding interrupt

(at vector $003) is executed if a capture-triggering event occurs on pin 14, PB0 (ICP),

i.e., when the ICF1 bit is set in the Timer/Counter Interrupt Flag Register (TIFR).

• Bit 2 – Res: Reserved Bit

This bit is a reserved bit in the AT90S4433 and always reads as zero.

• Bit 1 – TOIE0: Timer/Counter0 Overflow Interrupt Enable

When the TOIE0 bit is set (one) and the I-bit in the Status Register is set (one), the

Timer/Counter0 Overflow Interrupt is enabled. The corresponding interrupt (at vector

$006) is executed if an overflow in Timer/Counter0 occurs, i.e., when the TOV0 bit is set

in the Timer/Counter Interrupt Flag Register (TIFR).

• Bit 0 – Res: Reserved Bit

This bit is a reserved bit in the AT90S4433 and always reads as zero.

Bit

$39 ($59)

TOIE1

OCIE1

–

TICIE1

–

TOIE0

–

TIMSK

Read/Write

R/W

Initial Value

AT90LS4433-4AI 데이터시트(PDF) 28 Page - ATMEL Corporation

AT90LS4433-4AI 데이터시트(HTML) 28 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL